DAELIM DAYSTAR - Service Manual Download Page 49

Page: 49 / 214

4-11

Fuel System

Accelerator Adjustment

•

Do not adjust unless replacing the adjuster
screws.

•

Adjust the idling.(

⇨

3-8)

•

Adjust the operation of throttle grip.(

⇨

3-4)

•

Loosen the lock nut, turn the adjuster screws to
contact with accelerator pump cap, and then
adjust the accelerator pump rod clearance.

•

Tighten the lock nut.

Clearance : 0mm (0in)

●

Install the new o-ring to the float chamber
groove.

●

Install the float chamber and screws.

Assembly

Install the fuel tube and drain tube.

●

Install the new o-ring into carburetor intake
flange.

●

Assemble the carburetor between carburetor
insulator and connecting tube. Install the
carburetor assembly nut and tighten the
connecting tube bend screw.

●

Connect the choke cable and throttle cable.

●

Adjust the chock cable.(

⇨

3-5)

●

Install the throttle valve.(

⇨

4-5)

●

Adjust the throttle grip clearance.(

⇨

3-4)

Fuel Tube

Drain Tube

Connecting Tube

Throttle Stop Screw

Carburetor

CAUTION

△

Float Level Chamber

O-Ring

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands