DAELIM DAYSTAR - Service Manual Download Page 168 | Manualshive

Page: 168 / 214

background image

15-7

Hydraulic Brake

Brake Caliper

Removal

Remove the brake hose bolt and brake hose
from the brake caliper.
Remove the caliper from the front fork, then
remove the pad pin bolt, brake pad. (

14-4)

•

Avoid spilling brake fluid on painted, plastic,
or rubber parts.

•

A contaminated brake disk or pad reduces
stopping power. Discard contaminated pads
and clean the disk with a high quality brake
degreasing agent.

Disassembly

Remove the slide pin, caliper bracket, and boot
from caliper.
Must be replaced if the boot is damaged or
worn.
Cover the caliper with cloth in order to avoid
the Piston and brake fluid from leakage, and
the piston face down.
Blow the low pressure air slowly in the
assembly part of brake hose, and remove the
piston from caliper.

•

Do not use the high pressure air, or do not
close the air conditioner.

•

Do not put the hand into the caliper inside.

Remove the piston seal and dust seal.
Prevent the caliper inside from damaging.
Clean the caliper inside and piston with brake
fluid.

NOTE

!

CAUTION

△

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Hose

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Caliper

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Brake Hose Bolt

Caliper

Caliper

Seal

!

WARNING

△

«
...
166
167
168
169
170
...
»

Summary of Contents for DAYSTAR -























































































































































































































Reviews:

No comments

Related manuals for DAYSTAR -

Brand: Parkside Pages: 89

Brand: Parkside Pages: 28

WARRIOR YFM350XS

Brand: Yamaha Pages: 46

Brand: Happy Trails Pages: 3

Brand: Suzuki Pages: 440

Brand: Takegawa Pages: 2

SBL.04.650.10000/B

Brand: SW-Motech Pages: 2

Quantum hardcoated N30214-WK

Brand: National Cycle Pages: 13

990D0-31J50-CLE

Brand: Suzuki Pages: 12

Brand: SCA Pages: 5

Brand: Denali Pages: 5

Brand: Thunderbike Pages: 7

WOLVERINE R MAX 2021

Brand: Yamaha Pages: 190

Brand: Yamaha Pages: 194

WOLVERINE RMAX2 2024

Brand: Yamaha Pages: 196

Vstar XVS650T 2004

Brand: Yamaha Pages: 101

Brand: DYNATEK Pages: 13

990D0-E5500-000

Brand: Suzuki Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands