DAELIM DAYSTAR - Service Manual Download Page 133

Page: 133 / 214

13-6

Front Wheel/Front Fork/Steering

●

Tighten the forward screws first, then tighten
the rear screws.

●

After installing the brake hose, kill switch
cable, winker switch code and chock cable into
the cable guide, tighten the guide.

Inspection

●

Inspect the front axle for bent.

●

Install the front axle into V-block, and measure
it using a dial gauge.

Service Limit: Over 0.2mm

Front Wheel

Removal

●

Loosen the axle nut.

●

Raise and support the motorcycle using a jack.
Remove the screw from the speedometer cable.
Remove the axle nut, front axle, and front
wheel, and right side collar.

•

Do not operate the front brake lever after
removing the front wheel.

NOTE

Screw

Cable Guide

Screw

Speedometer Cable

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands