DAELIM DAYSTAR - Service Manual Download Page 159

Page: 159 / 214

14-10

Rear Wheel/Rear Brake/Suspension

●

Coat the lock nut with oil to the thread, and
install the rear cushion compressor attachment
into the damper rod.

●

Coat the upper joint with oil to the thread and
install it into the damper rod.

●

Fix the upper joint and tighten the lock nut.

Torque: 3.8kgf-m (38N.m)
Tools:

Rear cushion compressor
Rear cushion compressor attachment

Installation

●

Install the rear cushion.

●

Install the bolt

Torque: Upper bolt: 3.4kgf-m

Lower bolt: 3.4kgf-m

Rear Fork

Removal

●

Remove the rear wheel. (

⇨

14-3)

●

Remove the rear cushion. (

⇨

14-8)

●

Remove the chain cover.

●

Loosen the pivot bolt and nut using a box
wrench, and remove the rear fork.

Nut

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands