DAELIM DAYSTAR - Service Manual Download Page 66

Page: 66 / 214

6-10

Clutch, Gearshift

●

Install the lock nut by pressing clutch center
into the clutch center holder.

Torque : 6.5kgf-m (65N.m)
Tools:

Clutch center holder
Lock nut wrench, 20

24mm

Extension bar

●

Install the clutch spring, lifter plate and clutch
spring bolt diagonally several times.

•

Check if the pressure plate press the disc, and
plate exactly.

Primary Drive Gear

Removal

●

Remove the crank case.

●

Hold the flywheel using a flywheel holder.

●

Remove the primary drive gear lock nut.

Tools:

Flywheel holder
Lock nut wrench, 20

24mm

Extension bar

●

Remove the lock nut, primary drive gear, and
woodruff key.

●

Install the pressure plate, disk, plate and clutch
center into the clutch outer.

●

Coat the nut parts with clean engine oil, and
tighten the lock nut.

NOTE

Clutch Spring Bolt

Lifter Plate

Extension Bar

Lock Nut

Lock Nut Wrinch 20X24mm

Lock Nut Wrench

Extension Bar

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands