DAELIM DAYSTAR - Service Manual Download Page 160

Page: 160 / 214

14-11

Rear Wheel/Rear Brake/Suspension

Disassembly

●

Disassemble the rear sub fender.

●

Disassemble the chain slider.

●

Disassemble the rear fork pivot bearing.

●

Disassemble the dust seal and center collar.

●

Disassemble the pivot bush.

●

Inspect the center collar pivot bush for wear,
damage, and defect.

●

Check the dust seal for wear and damage.

●

Check the rear fork for wear and other damage.

●

Inspect the rear pivot fork bearing for wear or
damage if necessary replaced.

Assembly

●

Apply grease to the center collar, pivot bush,
and install them to the rear fork.

●

Assemble the chain slider.

●

Coat the dust seal lips with grease, and install it.

●

Assemble the rear sub fender.

•

Assemble carefully not to bend or damage the
sides of the seal.

Installation

●

Install the rear fork and tighten the pivot bolt.

Torque: 4.5kgf-m

●

Install the following.

- Rear cushion
- Chain cover.
- Rear wheel
- R/L lower cover

CAUTION

△

Chain Slider

Dust Seal

Center Color

Chain Slider

Dust Seal

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands