DAELIM DAYSTAR - Service Manual Download Page 170

Page: 170 / 214

15-9

Hydraulic Brake

Installation

Connect the brake hose to the caliper, and
install the 2 sheets of sealing washer and brake
hose bolt.

Torque: 3.4kgf-m

Install the slide pin cap.
Fill the brake fluid and bleed the mixed air.
(

15-3)

Master Cylinder

Removal

Disconnect the brake light switch wires from
the switch. Drain the brake fluid from the
hydraulic system. (

15-3)

Remove the brake hose from the master
cylinder.

•

Brake fluid can cause damage to painted,
plastic, and rubber surfaces.

If attached, place a rag over the these parts or
clean them with brake fluid or water. Cover the
hose joint part to prevent break fluid leakage.

•

Clean the removed parts with brake fluid, check
for the clogged passage with compressed air.

•

Do not allow dust and dirt to stick to the
removed parts.

Remove the master cylinder holder, and take
off the master cylinder.

Disassembly

Remove the rear mirror, brake lever, and stop
switch.
Remove the piston boot and snap ring form
master cylinder.

Tool: Snap ring plier

CAUTION

△

Brake Hose

Brake Hose Bolt

Master Cylinder

Brake Hose Bolt

“UP” Mark

Brake Lever

Brake Right Switch

Brake Hose Bolt

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands