DAELIM DAYSTAR - Service Manual Download Page 33

Page: 33 / 214

3-11

Maintenance

Brake Shoe Replacement

●

Replace the brake shoes if the arrow on the
brake arm aligns with the reference mark

“△”

on full application of the rear brake pedal.

Brake System

●

Inspect the front brake hoses for deterioration,
cracks. If there are signs of leakage, replace
them as soon as possible. Replace hoses as
required.

●

Inspect the rear brake pedal and brake rod for
looseness or damage. Tighten any loose
fittings. Replace them if necessary.

Brake Pedal Height

●

Perform brake pedal clearance adjustment
after adjusting brake pedal height.

Free play: 20~30mm(0.787~1.181in)

●

If adjustment is necessary, use the rear brake
adjusting nut.

●

after adjusting the brake pedal free play, check
the rear brake light switch operation and adjust
it if necessary.

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

▵

Mark

Arrow

Brake Hose

Brake Caliper

Brake Hose Bolt

Adjusting Nut

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands