DAELIM DAYSTAR - Service Manual Download Page 53

Page: 53 / 214

5-3

Engine Removal / Installation

Engine Removal

●

Drain the engine oil.(

⇨

2-3)

●

Remove the following

- Side cover(

⇨

12-2)

- Seat(

⇨

12-2)

- Fuel tank(

⇨

4-3)

- Mufflers(

⇨

12-3)

●

Disconnect the connector of the starter motor
cable, AC generator wire, gear change switch
wire.

●

Remove the battery negative cable, clutch cable,
high tension code. Remove the carburetor.

●

Remove the gear change pedal, L. rear cover
drive sprocket cover.

●

Remove the rear axle nut, drive chain adjuster.

●

Remove the drive sprocket after pushing the
rear wheel forward.

●

Remove the front engine hanger bolt, engine
hanger bracket.

●

Remove the rear engine hanger bolt.

Screw

Drive Sprocket

Drive Chain Guide

Clutch Cable

High Tension Code

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands