DAELIM DAYSTAR - Service Manual Download Page 119

Page: 119 / 214

10-14

Crank Case / Transmission / Crankshaft / Kick Starter

●

Tighten the left crankcase bolt ina crisscross
pattern in 2-3 steps.

Torque: 1.1kgf-m(11N.m)

●

Install the cam chain and set plate.

●

Install the disassembled parts.

●

Install the engine on the frame. (

⇨

Section 5)

●

After replacing the o-ring of the gear change
switch to a new one, coat the new o-ring with
engine oil, then install the switch pin into the
groove of the shift drum.

●

Tighten the right crankcase bolt.

Torque: 1.1kgf-m(11N.m)

Cam Chain

Breather Tube

Bolt

Gear Shift Drum Hole

Gear Change Switch

Pin

O-Ring

Summary of Contents for DAYSTAR -























































































































































































































Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands

DAELIM DAYSTAR -, Service Manual

Search results

Summary of Contents for DAYSTAR -

Reviews:

Related manuals for DAYSTAR -

Brands by name

Popular brands