DGS-3000 Series Layer 2 Managed Gigabit Ethernet Switch CLI Reference Guide
20
optional. For non combo ports, the user doesn't need to specify medium_type in the
command.
fiber
- Specify the fiber port.
copper
- Specify the copper port
speed
- Specify the port speed.
auto
- Specify the port auto negotiation speed.
capability_advertised
- Specify that the capability will be advertised.
10_half
- Specify the port speed to 10_half.
10_full
- Specify the port speed to 10_full.
100_half
- Specify the port speed to 100_half.
100_full
- Specify the port speed to 100_full.
1000_full
- Specify the port speed to 1000_full. Using master or slave mode in this
mode is optional.
10_half
- Specify the port speed to 10_half.
10_full
- Specify the port speed to 10_full.
100_half
- Specify the port speed to 100_half.
100_full
- Specify the port speed to 100_full.
1000_full
- Specify the port speed to 1000_full. While set port speed to 1000_full,user should
specify master or slave mode for 1000BASE-T interface, and leave the 1000_full without
any master or slave setting for other interface.
master
- (Optional) Specify that the port(s) will be set to master.
slave
- (Optional) Specify that the port(s) will be set to slave.
10g_full
- Specify the port speed to 10g_full.
auto_negotiation
- Specify that the auto-negotiation option will be configured.
restart_an
- Specify to restart the auto-negotiation process.
remote_fault_advertised
- Specify that the remote fault advertisement option will be
configured.
disable
- Specify to disable remote fault advertisement.
offline
- Specify that a local device may indicate Offline prior to powering off, running
transmitter tests, or removing the local device from the active configuration. If it is set
and detected offline, it will advertise at the next auto-negotiation. It interacted for
1000Mbps MAUs.
link_fault
- Specify that if set and local device was detected, a Link_Failure condition
indicated by the loss of synchronization, will advertise at the next auto-negotiation. It
interacted for 1000Mbps MAUs.
auto_negotiation_error
- Specify the resolution which precludes operation between a
local device and link partner advertised at the next auto-negotiation. It interacted for
1000Mbps MAUs.
flow_control
- Turns on or turns off the flow control on one or more ports by enabling or
disabling this function.
enable
- Specify that the flow control option will be enabled.
disable
- Specify that the flow control option will be disabled.
learning
- Turns on or turns off the MAC address learning on one or more ports.
enable
- Specify that the learning option will be enabled.
disable
- Specify that the learning option will be disabled.
state
- Enables or disables the specified port. If the specificed ports are in error-disabled status,
configure their state to enable will recover these ports from disabled to enable state.
enable
- Specify that the port state will be enabled.
disable
- Specify that the port state will be disabled.
mdix
- The MDIX mode can be specified as auto, normal, and cross. If set to the normal state,
the port is in the MDIX mode and can be connected to PC NIC using a straight cable. If set to
the cross state, the port is in the MDI mode, and can be connected to a port (in the MDIX
mode) on another switch through a straight cable.
auto
- Specify that the MDIX mode for the port will be set to auto.
normal
- Specify that the MDIX mode for the port will be set to normal.
cross
- Specify that the MDIX mode for the port will be set to cross.
description
- Specify the description of the port interface.
<desc 1-32>
- Enter the port interface description. This value can be up to 32 characters long.
clear description
- (Optional) Specify that the description field will be cleared.
auto_speed_downgrade
- Specify to enable or disable the option to automatically downgrade
Summary of Contents for DGS-3000 series
Page 1: ......