manualshive.com logo in svg

Canon Oce Colr Wave 500, Operation Manual

Share
Download
Canon Oce Colr Wave 500 Operation Manual Download Page 292

Load a media roll

Introduction

You can load standard and custom media on your printer.

Before you begin

Before you load a roll on the printer, make sure your media has been configured.
• For standard media you can configure and enable a media profile in Océ Express WebTools.

For more information, see 

Configure the media profiles on page 195

.

• Make sure the size is configured and enabled in Océ Express WebTools. For more information,

see 

Configure the media sizes on page 198

. If your media size is not present in the list, you can

create a custom media size. For more information, see 

Create a custom media size on

page 197

.

IMPORTANT

• Do not use dented media rolls to prevent damage to the imaging devices.
• Do not open the media drawer during the print process.
• Do not open more than one media drawer at the same time to prevent overbalance of the

printer.

CAUTION

Watch your fingers when you handle the media roll.

Procedure

1.

Pull firmly to open the media drawer. 

2.

Place the new media roll on the roll loading station.

3.

Pull (1) the handle of the roll holder locking mechanism toward you. 
Slide (2) the roll holder into the right side of the core of the new media roll.

Load a media roll

292

Chapter 5 - Maintain the Printing System

Summary of Contents for Oce Colr Wave 500









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands