manualshive.com logo in svg

Canon Oce Colr Wave 500, Operation Manual

Share
Download
Canon Oce Colr Wave 500 Operation Manual Download Page 160

Set the long plot mode

Introduction

When the long plot mode is enabled, the system will be able to print TIFF, HP-GL, HP-GL2 and HP-
RTL plots up to 175 meter with good quality. Transformation such as scaling and rotating are not
guaranteed in this mode. For other formats such as PS and PDF, the system will print in "normal"
mode, with a maximum plot length of 22 meter.

For the printer to be able to print long prints, the print quality can be reduced.

Procedure

1.

Open the [Preferences] - [Print job defaults] tab.

2.

Click on [Edit] in the [General (non-postscript) rasterization settings] section or click on the [Long
plot mode] setting.

3.

Enable or disable. The setting is enabled when you check the box.

4.

Click [Ok] to confirm, or [Cancel] to reject your entries.

Set the long plot mode

160

Chapter 3 - Define your Workflow with Océ Express WebTools

Summary of Contents for Oce Colr Wave 500









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands