manualshive.com logo in svg

Canon Oce Colr Wave 500, Operation Manual

Share
Download
Canon Oce Colr Wave 500 Operation Manual Download Page 124

Set the default print preset 

Introduction

With a preset you can predefine the settings you need for a print job from USB or an external
location.

Print has four preset categories: [Media], [Layout], [Image], and [Finishing]. For each category you
can set one default preset in Océ Express WebTools. The default preset is automatically used
when you press the green button on the user panel.

NOTE

You can always find a short explanation of the setting in the tooltip.

Procedure

1.

Open the [Preferences] - [Print job defaults] tab.

2.

Under [User panel configuration: Default presets for print] select the preset category you want to
change, for example [Default layout preset].

3.

Select the setting you want to use as the default preset, for example [Standard half size]. 
Select [Custom] to make your custom preset default.

4.

Click [Ok] to confirm, or [Cancel] to reject your entries.

After you finish

To make sure your preset is active on the user panel, press the home button on the home screen
of the user panel.

Set the default print preset

124

Chapter 3 - Define your Workflow with Océ Express WebTools

Summary of Contents for Oce Colr Wave 500









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands