manualshive.com logo in svg

Canon Oce Colr Wave 500, Operation Manual

Share
Download
Canon Oce Colr Wave 500 Operation Manual Download Page 28

The Hardware

The components of the printer (front)

12

11

1

2

3

4

5 6 7

8

9

10

14

13

15

Component - function table

No

Component

Description / Function

1

[media drawers] 

Media drawers with 2 media rolls

2

[lower left side cover]

Cover at the bottom left of the device

3

[lower front cover] 

Door to access the media path

4

[top cover] 

Component that covers the top surface of the de-
vice

5

[toner cartridge (cyan)] 

Toner cassette for cyan Océ TonerPearls®

6

[toner cartridge (yellow)] 

Toner cassette for yellow Océ TonerPearls®

7

[toner cartridge (black)] 

Toner cassette for black Océ TonerPearls®

8

[toner cartridge (magenta)] 

Toner cassette for magenta Océ TonerPearls®

9

[transparent top cover] 

Door to access the print surface / media output
section

10

[top delivery tray] 

Delivery tray that collects the printed output

11

[USB port] 

USB connector to use a USB key to print from or
to scan to

12

Océ ClearConnect: multi-touch [user
panel] 

The Océ ClearConnect user panel allows the user
to start copy, scan, or print jobs, and to monitor
the system and the job status.

4

The Hardware

28

Chapter 2 - Get to Know the Printing System

Summary of Contents for Oce Colr Wave 500









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands