manualshive.com logo in svg

Canon Oce Colr Wave 500, Operation Manual

Share
Download
Canon Oce Colr Wave 500 Operation Manual Download Page 132

Set a default print destination

Introduction

You can configure the default print destination in Océ Express WebTools. When the destination of
a print job is not specified in the job ticket or when there is no job ticket, the job is sent to a
default destination. You can choose between two default print destinations:
• [Both queue and Smart Inbox]: the job is printed automatically and stored in the Smart Inbox.
• [Only Smart Inbox]: the job is sent to the Smart Inbox and you have to start it locally.

NOTE

You can only set the default print destination, when the [Override destination of print jobs]

setting is set to [No, as specified in the job ticket]. You can find this setting under [Preferences] -

[System defaults] - [Job management].

Procedure

1.

Select the [Preferences] - [System defaults] tab.

2.

Click on [Edit] in the [Job management] section, or click on the setting [Default destination of
print jobs].

3.

Select [Both queue and Smart Inbox] or [Only Smart Inbox].

4.

Click [Ok] to confirm, or [Cancel] to reject your entries.

After you finish

Your preferred print destination is now default. All print jobs are sent to this destination when
you do not make other settings.

Set a default print destination

132

Chapter 3 - Define your Workflow with Océ Express WebTools

Summary of Contents for Oce Colr Wave 500









































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands