manualshive.com logo in svg

Atmel AVR XMEGA AU series, Manual

The Atmel AVR XMEGA AU series offers high-performance 8/16-bit microcontrollers with advanced features. Get your free user manual downloads for programming and usage instructions from manualshive.com. Stay informed with detailed manuals for optimal performance and functionality. Experience the power of Atmel AVR XMEGA AU series with ease.

Share
Download
background image

332

8331B–AVR–03/12

Atmel AVR XMEGA AU

26.7.2

STATUS – Status register

• Bit 7:2 – Reserved

These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.

• Bit 1 – ZERO: Checksum Zero 

This flag is set if the CHECKSUM is zero when the CRC generation is complete. It is automati-
cally cleared when a new CRC source is selected. 

When running CRC-32 and appending the checksum at the end of the packet (as little endian),
the final checksum shold be 0x2144df1c, and not zero. However, if the checksum is comple-
mented before it is appended (as little endian) to the data, the final result in the checksum
register will be zero. 

See the description of CHECKSUM to read out different versions of the CHECKSUM.

• Bit 0 – BUSY: Busy

This flag is read as one when a source configuration is selected and as long as the source is
using the CRC module. If the I/O interface is selected as the source, the flag can be cleared by
writing a one this location. If a DMA channel if selected as the source, the flag is cleared when
the DMA channel transaction is completed or aborted. If flash memory is selected as the source,
the flag is cleared when the CRC generation is completed.

26.7.3

DATAIN – Data Input Register

• Bit 7:0 – DATAIN[7:0]

This register is used to store the data for which the CRC checksum is computed

. A new CHECK-

SUM is ready one clock cycle after the DATAIN register is written.

0110

DMACH2

DMA controller channel 2

0111

DMACH3

DMA controller channel 3

1xxx

—

Reserved for future use

Table 26-2.

CRC source select (Continued).

SOURCE[3:0]

Group configuration

Description

Bit

7

6

5

4

3

2

1

0

+0x02

–

–

–

–

–

–

ZERO

BUSY

STATUS

Read/Write

R

R

R

R

R

R

R

R/W

Initial Value

0

0

0

0

0

0

0

0

Bit

7

6

5

4

3

2

1

0

+0x03

DATAIN[7:0]

DATAIN

Read/Write

W

W

W

W

W

W

W

W

Initial  Value

0

0

0

0

0

0

0

0

Summary of Contents for AVR XMEGA AU series

































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AVR XMEGA AU series

ZKTeco SC800 User Manual preview
SC800
Brand: ZKTeco Pages: 123
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78
Danfoss AME 335 Installation Manual preview
AME 335
Brand: Danfoss Pages: 20
Danfoss CCR2 Installation Manual preview
CCR2
Brand: Danfoss Pages: 64
Danfoss ERC 211 User Manual preview
ERC 211
Brand: Danfoss Pages: 36
tbs electronics Omnicharge Solar OCS 100-20 Installation Manual preview
Omnicharge Solar OCS 100-20
Brand: tbs electronics Pages: 64
Acuity Controls nLight ECLYPSE Safety Instructions preview
nLight ECLYPSE
Brand: Acuity Controls Pages: 5
Bard CompleteStat-Series CS9B-THO Product Manual preview
CompleteStat-Series CS9B-THO
Brand: Bard Pages: 2
YASKAWA PG-X2 Instructions Manual preview
PG-X2
Brand: YASKAWA Pages: 12
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Brand: H.E. Anderson Pages: 11
Levven GPC20 Instruction Sheet preview
GPC20
Brand: Levven Pages: 2
Holars AS H-TAG User Manual preview
H-TAG
Brand: Holars AS Pages: 15

Brands by name

Popular brands

Load more brands