ARTERY AT32F425 Series Reference Manual Download Page 401 | Manualshive

Page: 401 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 401

Ver 2.01

that channel is complete. The application must wait for the
generation of the channel disabled interrupt before treating
the channel as disabled.

Bit 29

ODDFRM

0x0

rw

Odd frame
This bit is set / cleared by the application to indicate that
the OTG host must perform a transfer in an odd frame. This
bit is applicable for periodic transfers (synchronous and
interrupt) only.
0: Even frame
1: Odd frame

Bit 28: 22 DEVADDR

0x00

rw

Device address
This field is used to select the device that can serve as the
data source or receiver.

Bit 21: 20 MC

0x0

rw

Multi count (MC)
This field indicates to the host the number of transfers that
must be performed per frame for the periodic endpoint.
00: Reserved. This field generates undefined results.
01: 1 transaction
10: 2 transactions per frame
11: 3 transactions per frame
This field must be set to at least 0x01.

Bit 19: 18 EPTYPE

0x0

rw

Endpoint type
Indicates the transfer type selected.
00: Control transfer
01: Synchronous transfer
10: Bulk transfer
11: Interrupt transfer

Bit 17

LSPDDEV

0x0

rw

Low-speed device
The application sets this bit to indicate that this channel is
communicating to a low-speed device.

Bit 16

Reserved

0x0

resd

Kept at its default value.

Bit 15

EPTDIR

0x0

rw

Endpoint direction
Indicates whether the transfer is in IN or OUT.
0: OUT
1: IN

Bit 14: 11 EPTNUM

0x0

rw

Endpoint number
Indicates the endpoint number on the device (serving as
data source or receiver)

Bit 10: 0

MPS

0x000

rw

Maximum packet size
Indicates the maximum packet size of the corresponding
port.

20.6.4.9 OTGFS host channelx interrupt register ( OTGFS_HCINTx) (x

= 0...15, where x= channel number)

This register contains the status of a channel related to USB and AHB events, as shown in

The application must read this register when the host channels interrupt bit is set in the controller
interrupt register. Before reading this register, the application must read the host all channels interrupt
register to get the exact channel number ofr the host channel-n interrupt register. The application must
clear the corresponding bit in this register to clear the corresponding bits in the OTGFS_HAIN and
OTGFS_GINTSTS registers.

Bit

Register

Reset value

Type

Description

Bit 31: 11 Reserved

0x000000

resd

Kept at its default value.

Bit 10

DTGLERR

0x0

rw1c

Data toggle error
This bit can only be set by the controller. The application
must write 1 to clear this bit.

Bit 9

FRMOVRUN

0x0

rw1c

Frame overrun
This bit can only be set by the controller. The application
must write 1 to clear this bit.

Bit 8

BBLERR

0x0

rw1c

Babble error
This bit can only be set by the controller. The application
must write 1 to clear this bit.

Bit 7

XACTERR

0x0

rw1c

Transaction error
Indicates one of the following errors occurred on the USB

«
...
399
400
401
402
403
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

ShareCenter DNS-320L

Brand: D-Link Pages: 4

Brand: Data Translation Pages: 98

Brand: FOR-A Pages: 39

IAR KickStart Kit TWR-K60N512-IAR

Brand: IAR SYSTEMS Pages: 8

Brand: ETAS Pages: 82

Brand: Kontron Pages: 62

Brand: FiberHome Pages: 2

Brand: ADS Technologies Pages: 21

LinkStation 500

Brand: Buffalo Pages: 139

Brand: ekwb Pages: 16

Core 2 Duo E4300

Brand: Intel Pages: 55

Brand: Avaya Pages: 2

Brand: COP-USA Pages: 114

Brand: Lenze Pages: 46

Brand: StarTech.com Pages: 2

Brand: DAQ Pages: 23

DAS-1700 Series

Brand: Keithley Pages: 112

Mercury Elite Pro Dual

Brand: OWC Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands