manualshive.com logo in svg

ARTERY AT32F425 Series, Reference Manual

The ARTERY AT32F425 Series Reference Manual is a comprehensive guide for users to navigate the features and functions of their device. Download the manual for free from our website to access detailed instructions and troubleshooting tips. Ensure optimal performance with the help of this essential resource.

Share
Download
background image

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 399 

 

Ver 2.01

 

20.6.4.7  OTGFS host port control and status register ( OTGFS_HPRT) 

This register is valid only in host mode. Currently, the OTG host supports only one port. 
This register contains USB port-relatd information such as USB reset, enable, suspend, resume, connect 
status and test mode, as show in 

Figure 21-2

. The register of type rw1c can interrupt the application 

through the host port interrupt bit in the controller interrupt register. Upon a port interrupt, the application 
must  read  this  register and  clear  the bit  that  caused  the interrupt.  For  the  register of  type  rw1c,  the 
application must write 1 to clear the interrupt. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 19  Reserved 

0x0000 

resd 

Kept at its default value. 

Bit 18: 17  PRTSPD 

0x0 

ro 

Port speed 
Indicates the speed of the device connected to this port. 
00: Reserved 
01: Full speed 
10: Low speed 
11: Reserved 

Bit 16: 13  PRTTSTCTL 

0x0 

rw 

Port test control 
The application writes a non-zero value to this field to put 
the port into test mode, and the port gives a corresponding 
signal. 
0000: Test mode disabled 
0001: Test_J mode 
0010: Test_K mode 
0011: Test_SE0_NAK mode 
0100: Test_Packet mode 
0101: Test_Force_Enable 
Others: Reserved 

Bit 12 

PRTPWR 

0x0 

rw 

Port power 
The application uses this bit to control power supply to this 
port (by writing 1 or 0) 
0: Power off 
1: Power on 
Note:  This  bit  is  not  associated  with  interfaces.  The 
application must follow the programming manual to set this 
bit for various interfaces. 

Bit 11: 10  PRTLNSTS 

0x0 

ro 

Port line status 
Indicates the current logic status of the USB data lines. 
Bit [10]: Logic level of D+ 
Bit [11]: Logic level of D– 

Bit 9 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 8 

PRTRST 

0x0 

rw 

Port reset 
When this bit is set by the application, a reset sequence is 
started on this port. The application must calculate the time 
required for the reset sequence, and clear this bit after the 
reset sequence is complete. 
0: Port not in reset 
1: Port in reset 
The  application  must  keep  this  bit  set  for  a  minimum 
duration defined in Section 7.1.7.5 of USB 2.0 specification 
to  start  a  reset  on  the  port.  In  addition  to  this,  the 
application can make this bit set for another 10 ms to the 
minimum  duration,  before  clearing  this  bit.  There  is  no 
maximum limit set by the USB standard. 

Bit 7 

PRTSUSP 

0x0 

rw1s 

Port suspend 
The  application  sets  this  bit  to  put  this  port  in  suspend 
mode. In this case, the controller only stops sending SOF. 
The application must set the port clock stop bit in order to 
disable the PHY clock. 
The  read  value  of  this  bit  reflects  the  current  suspend 
status of the port. 
This bit is cleared by the controller when a remote wakeup 
signal  is  detected  or  when  the  application  sets  the  port 
reset  bit  or  port  resume  bit  in  this  register,  or  sets  the 

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

D-Link PCMCIA WIRELESS ASAPTER DWL-650 Quick Install Manual preview
PCMCIA WIRELESS ASAPTER DWL-650
Brand: D-Link Pages: 5
D-Link PowerLine DHP-W611AV User Manual preview
PowerLine DHP-W611AV
Brand: D-Link Pages: 78
Keithley 7707 User Manual preview
7707
Brand: Keithley Pages: 59
Lattice Semiconductor ECP5 Versa Quick Start Manual preview
ECP5 Versa
Brand: Lattice Semiconductor Pages: 15
Oracle Talari E1000 Installation Manual preview
Talari E1000
Brand: Oracle Pages: 24
Ubiquiti PowerBeam AC Gen2 Quick Start Manual preview
PowerBeam AC Gen2
Brand: Ubiquiti Pages: 22
C-Smartlink DMH25 Manual preview
DMH25
Brand: C-Smartlink Pages: 7
ZALMAN CNPS5X PERFORMA User Manual preview
CNPS5X PERFORMA
Brand: ZALMAN Pages: 8
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Brand: Symantec Pages: 100
Variscite VAR-EXT-CB103 Manual preview
VAR-EXT-CB103
Brand: Variscite Pages: 17
Corsair LL140 RGB Series Manual preview
LL140 RGB Series
Brand: Corsair Pages: 30
Airaya AI108-1-050 Quick Install Manual preview
AI108-1-050
Brand: Airaya Pages: 28
CAMBRIONIX OEM-U8S User Manual preview
OEM-U8S
Brand: CAMBRIONIX Pages: 43
EK EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB User Manual preview
EK-Mana MSI MAG Z690 TORPEDO EK X D-RGB
Brand: EK Pages: 9
Gigamon GigaVUE H Series Hardware Installation Manual preview
GigaVUE H Series
Brand: Gigamon Pages: 55
Data-Tronix DT-ATSC-IP-8 User Manual & Installation Manual preview
DT-ATSC-IP-8
Brand: Data-Tronix Pages: 15
DataExpert ATX431 User Manual preview
ATX431
Brand: DataExpert Pages: 48
Magnescale MG80-EI Operating Manual preview
MG80-EI
Brand: Magnescale Pages: 73

Brands by name

Popular brands

Load more brands