manualshive.com logo in svg

ARTERY AT32F425 Series, Reference Manual

The ARTERY AT32F425 Series Reference Manual is a comprehensive guide for users to navigate the features and functions of their device. Download the manual for free from our website to access detailed instructions and troubleshooting tips. Ensure optimal performance with the help of this essential resource.

Share
Download
background image

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 414 

 

Ver 2.01

 

Bit 3 

TIMEOUT 

0x0 

rw1c 

Timeout condition 
Applies to control IN endpoints only. This bit indicates that 
the controller has detected a timeout condition for the last 
IN token on this endpoint. 

Bit 2 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 1 

EPTDISD 

0x0 

rw1c 

Endpoint disabled interrupt 
This bit indicates that the endpoint is disabled according to 
the application’s request. 

Bit 0 

XFERC 

0x0 

rw1c 

Transfer completed interrupt 
Inidcates that the programmed transfers are complete on 
the AHB and on the USB for this endpoint. 

20.6.5.14 

OTGFS device OUT endpoint-x interrupt register 

(OTGFS_DOEPINTx) (x=0

…

7, where x if endpoint number) 

This register indicates the status of an endpoint with repect to USB and AHB-related events, as shown 
in Figure 20-2. When the OEPINT bit of the OTGFS_GINTSTS register is set, the application must first 
read the OTGFS_DAINT register to get the exact endpoint number in which the event occurs, before 
reading the endpoint interrupt registers. The application must clear the appropriate bit in this register to 
clear the correspoinding bits in the OTGFS_DAINT and OTGFS_GINTST registers. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 7 

Reserved 

0x0000001 

resd 

Kept at its default value. 

Bit 6 

B2BSTUP 

0x0 

rw1c 

Back-to-back SETUP packets received 
Indicates  that  more  than  three  back-to-back  SETUP 
packets are received. 

Bit 5 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 4 

OUTTEPD 

0x0 

rw1c 

OUT token received when endpoint disabled 
Applies to control OUT endpoints only. 
Indicates  that  an  OUT  token  was  received  when  the 
endpoint  has  not  yet  been  enabled.  An  interrupt  is 
generated on  the  endpoint  for  which  an  OUT  token  was 
received. 

Bit 3 

SETUP 

0x0 

rw1c 

SETUP phase done 
Applies to control OUT endpoints only. 
Indicates that the SETUP stage for the control endpoint is 
complete and no more back-to-back SETUP packets were 
received  for  the  current  control  transfer.  Upon  this 
interrupt, the application can decode the received SETUP 
data packets.

 

Bit 2 

Reserved 

0x0 

resd 

Kept at its default value. 

Bit 1 

EPTDISD 

0x0 

rw1c 

Endpoint disabled interrupt 
Indicates  that  the  endpoint  is  disabled  according  to  the 
application’s request. 

Bit 0 

XFERC 

0x0 

rw1c 

Transfer completed interrupt 
Inidcates that the programmed transfers are complete on 
the AHB and on the USB for this endpoint. 

20.6.5.15 

OTGFS device IN endpoint 0 transfer size register 

(OTGFS_DIEPTSIZ0)   

The application must set this register before enabling endpoint 0. Once the endpoint 0 is enabled using 
the endpoint enable pin in the device endpoint 0 control register, the controller modifies this register. The 
application can only read this register as long as the controller clears the endpoint enable bit. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 21  Reserved 

0x000 

resd 

Kept at its default value. 

Bit 20: 19  PKTCNT 

0x0 

rw 

Packet count 
Indicates the total number of USB packets that consistute 
the transfer size of data for the endpoint 0. 
This field is decremented every time a packet is read from 
the transmit FIFO (maximum packet size or short packet) 

Bit 18: 7 

Reserved 

0x000 

resd 

Kept at its default value. 

Bit 6: 0 

XFERSIZE 

0x00 

rw 

Transfer size 
Indicates the transfer size (in bytes) for the endpoint 0. The 

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

D-Link ShareCenter Quattro DNS-345 Quick Install Manual preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 40
D-Link ShareCenter Quattro DNS-345 Datasheet preview
ShareCenter Quattro DNS-345
Brand: D-Link Pages: 4
D-Link MYDLINK DNR-322L Datasheet preview
MYDLINK DNR-322L
Brand: D-Link Pages: 4
D-Link mydlink DNR-312L Quick Install Manual preview
mydlink DNR-312L
Brand: D-Link Pages: 8
D-Link DNS-722-4 Quick Install Manual preview
DNS-722-4
Brand: D-Link Pages: 16
D-Link DNS-722-4 User Manual preview
DNS-722-4
Brand: D-Link Pages: 88
ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
Sangoma A400 Installation Manual preview
A400
Brand: Sangoma Pages: 6
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
UNA AUTOMATION DIFRA Installation Manual preview
DIFRA
Brand: UNA AUTOMATION Pages: 20
ICP DAS USA PDS-734D Quick Start Manual preview
PDS-734D
Brand: ICP DAS USA Pages: 8
East Coast Datacom PDS-1/10G User Manual preview
PDS-1/10G
Brand: East Coast Datacom Pages: 19
Analog Devices EZ-Extender Analog 120-Pin Probing Board Manual preview
EZ-Extender Analog 120-Pin Probing Board
Brand: Analog Devices Pages: 29
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
Medel RONDO 3 Quick Manual preview
RONDO 3
Brand: Medel Pages: 28
IEI Technology WAFER-ULT4 User Manual preview
WAFER-ULT4
Brand: IEI Technology Pages: 136
Delta AH10EN-5A Series Operation Manual preview
AH10EN-5A Series
Brand: Delta Pages: 132
Xinje VH5 Series User Manual preview
VH5 Series
Brand: Xinje Pages: 76

Brands by name

Popular brands

Load more brands