ARTERY AT32F425 Series Reference Manual Download Page 62

Page: 62 / 429

AT32F425

Series Reference Manual

2022.03.30

Page 62

Ver 2.01

Sety by hardware. Cleared by writing to the RSTFC bit.
0: No software reset occurs
1: Software reset occurs.

Bit 27

PORRSTF

0x1

POR/LVR reset flag
Sety by hardware. Cleared by writing to the RSTFC bit.
0: No POR/LVR reset occurs
1: POR/LVR reset occurs.

Bit 26

NRSTF

0x1

NRST pin reset flag
Sety by hardware. Cleared by writing to the RSTFC bit.
0: No NRST pin reset occurs
1: NRST pin reset occurs

Bit 25

Reserved

0x0

resd

Kept at its default value.

Bit 24

RSTFC

0x0

Reset flag clear
Cleared by writing 1 through software.
0: No effect
1: Clear the reset flag.

Bit 23: 2 Reserved

0x000000

resd

Kept at its default value.

Bit 1

LICKSTBL

0x0

LICK stable
0: LICK is not ready.
1: LICK is ready.

Bit 0

LICKEN

0x0

LICK enable
0: Disabled
1: Enabled

4.3.11 APB peripheral reset register (CRM_APBRST)

Access: 0 wait state, accessible by words, half-words and bytes.

Bit

Name

Reset value

Type

Description

Bit 31:23

Reserved

0x0000

resd

Kept at its default value.

Bit 22

GPIOFRST

GPIOF reset
0: Does not reset GPIOF
1: Reset GPIOF

Bit 21

Reserved

0x0

resd

Kept at its default value.

Bit 20

GPIODRST

GPIOD reset
0: Does not reset GPIOD
1: Reset GPIOD

Bit 19

GPIOCRST

GPIOC reset
0: Does not reset GPIOC
1: Reset GPIOC

Bit 18

GPIOBRST

GPIOB reset
0: Does not reset GPIOB
1: Reset GPIOB

Bit 17

GPIOARST

GPIOA reset
0: Does not reset GPIOA
1: Reset GPIOA

Bit 16: 13 Reserved

0x0

resd

Kept at its default value.

Bit 12

OTGFS1RST

0x0

OTGFS1 reset
0: Does not reset OTGFS1
1: Reset OTGFS1

Bit 11: 0

Reserved

0x0000

resd

Kept at its default value.

4.3.12 PLL configuration register (CRM_PLL)

Access: 0 wait state, by words, half-words and bytes.

Bit

Name

Reset value

Type

Description

Bit 31

PLLCFGEN

0x0

PLL configuration enable
0: Common integer multiplication mode, which is done by
PLL_FREF and PLLMULT registers.
1: Flexible configuration mode, which is done by

LL_MS/PLL_NS/PLL_FR registers.

Bit 30: 27 Reserved

0x0

resd

Kept at its default value.

Bit 26: 24 PLL_FREF

0x0

PLL input clock selection
This field is valid only if PLLCFGEN=0.
000: 3.9 ~ 5 MHz
001: 5.2 ~ 6.25 MHz

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Search results

Summary of Contents for AT32F425 Series

Reviews:

Related manuals for AT32F425 Series

Brands by name

Popular brands

ARTERY AT32F425 Series, Reference Manual

Search results

Summary of Contents for AT32F425 Series

Reviews:

Related manuals for AT32F425 Series

Brands by name

Popular brands