ARTERY AT32F425 Series Reference Manual Download Page 231 | Manualshive

Page: 231 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 231

Ver 2.01

100: C1ORAW signal
101: C2ORAW signal
110: C3ORAW signal
111: C4ORAW signal

Bit 3

DRS

0x0

rw

DMA request source
0: Capture/compare event
1: Overflow event

Bit 2

CCFS

0x0

rw

Channel control bit flash selection
This

bit

only

acts

on

channels

that

have

complementaryoutput. If the channel contro bits are
buffered:

0: Control bits are updated by setting the HALL bit
1: Control bits are updated by setting the HALL bit or a
rising edge on TRGIN.

Bit 1

Reserved

0x0

resd

Kept at its default value.

Bit 0

CBCTRL

0x0

rw

Channel buffer control
This bit acts on channels that have complementary
output.
0: CxEN, CxCEN and CxOCTRL bits are not buffered.
1: CxEN, CxCEN and CxOCTRL bits are not buffered.

14.4.4.3 TMR15 slave timer control register (TMR15_STCTRL)

Bit

Register

Reset value

Type

Description

Bit 31: 8

Reserved

0x0

resd

Kept at its default value.

Bit 7

STS

0x0

rw

Subordinate TMR synchronization
If enabled, master and slave timer can be synchronized.
0: Disabled
1: Enabled

Bit 6: 4

STIS

0x0

rw

Subordinate TMR input selection
This field is used to select the subordinate TMR input.
000: Internal selection 0 (IS0)
001: Internal selection 1 (IS1)
010: Internal selection 2 (IS2)
011: Internal selection 3 (IS3)
100: C1IRAW input detector (C1INC)
101: Filtered input 1 (C1IF1)
110: Filtered input 2 (C1IF2)
111: External input (EXT)
Pleaser refer to Table 14-3 and 14-5 for more information
on ISx for each timer.

Bit 3

Reserved

0x0

resd

Kept at its default value.

Bit 2: 0

SMSEL

0x0

rw

Subordinate TMR mode selection
000: Slave mode is disabled
001: Encoder mode A
010: Encoder mode B
011: Encoder mode C
100:  Reset  mode

—

Rising edge of the TRGIN input

reinitializes the counter
101: Suspend mode — The counter starts counting when
the TRGIN is high
110: Trigger mode — A trigger event is generated at the
rising edge of the TRGIN input
111: External clock mode A

—

Rising edge of the TRGIN

input clocks the counter
Note: Please refer to count mode section for the details on
encoder mode A/B/C.

14.4.4.4 TMR15 DMA/interrupt enable register (TMR15_IDEN)

Bit

Register

Reset value

Type

Description

Bit 15

Reserved

0x0

resd

Kept at its default value.

Bit 14

TDEN

0x0

rw

Trigger DMA request enable
0: Disabled
1: Enabled

«
...
229
230
231
232
233
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

Brand: D-Link Pages: 12

Brand: Ebyte Pages: 14

Brand: Black Box Pages: 9

Protege PRT-PX16-PCB

Brand: ICT Pages: 34

DL-DVI-Vision-IP Series

Brand: G&D Pages: 228

CY62136EV30 MoBL

Brand: Cypress Semiconductor Pages: 12

netHOST NHST-T100

Brand: hilscher Pages: 75

Brand: Stepper Motor Canada Pages: 5

ARC-12x4 Series

Brand: Areca Pages: 2

Brand: Dave Embedded Systems Pages: 79

Brand: Renesas Pages: 4

Brand: VIA Technologies Pages: 2

Brand: Trend Micro Pages: 2

EK-Quantum Vector FTW3 RTX 2080 Ti

Brand: ekwb Pages: 3

CP 040 RS422/485

Brand: YASKAWA Pages: 87

Brand: WIN Enterprises Pages: 25

Brand: Rajant Pages: 93

Brand: Abus Pages: 98

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands