ARTERY AT32F425 Series Reference Manual Download Page 395 | Manualshive

Page: 395 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 395

Ver 2.01

Bit 15: 0

INEPT0TXSTADDR

0x0200

ro/rw

IN Endpoint FIFO0 transmit SRAM start address
This field contains the memory start address of the IN
Endpoint FIFO0 transmit SRAM.

20.6.3.11

OTGFS non-periodic Tx FIFO size/request queue status

register (OTGFS_GNPTXSTS)

This register is valid in host mode only. It is a read-only register that contains the available space
information for the Non-periodic TxFIFO and the Non-periodic Transmit Request Queue.

Bit

Register

Reset value

Type

Description

Bit 31

Reserved

0x0

resd

Kept at its default value.

Bit 30: 24 NPTXQTOP

0x00

ro

Top of the Non-periodic transmit request queue
Indicates that the MAC is processing the request from the
non-periodic transmit request queue.
Bit [30: 27]: Channel/Endpoint number
Bit [26: 25]:
00: IN/OUT token
01: Zero-length transmit packet (device IN/host OUT)
10: PING/CSPLIT token
11: Channel halted command
Bit [24]: Terminate (last request for the selected
channel/endpoint)

Bit 23: 16 NPTXQSPCAVAIL

0x08

ro

Non-periodic transmit request queue space available
Indicates the amount of space available in the non-periodic
transmit request queue. This queue supports both IN and
OUT requests in host mode.
00: Non-periodic transmit request queue is full
01: 1 location available
02: 2 locations available
N: n locations available (0 ≤ n ≤ 8)
Others: Reserved
Reset value: Configurable

Bit 15: 0

NPTXFSPCAVAIL

0x0200

ro

Non-periodic TxFIFO space available
Indicates the amount of space available in the non-periodic
TxFIFO. Values are in terms of 32-bit words.
00: Non-periodic transmit FIFO is full
01: 1 location available
02: 2 locations available
N: n locations available (0 ≤ n ≤ 256)
Others: Reserved
Reset value: Configurable

20.6.3.12

OTGFS general controller configuration register

(OTGFS_GCCFG)

Bit

Register

Reset value

Type

Description

Bit 31: 22 Reserved

0x000

resd

Kept at its default value.

Bit 21

VBUSIG

0x0

rw

VBUS ignored
When this bit is set, the OTGFS controller does not monitor
the Vbus pin voltage, and assumes that the Vbus is always
active in both host and device modes, and leaves the Vbus
pin for other purposes.
0: Vbus is not ignored
1: Vbus is ignored, and is deemed as always active

Bit 20

SOFOUTEN

0x0

rw

SOF output enable
0: No SOF pulse output
1: SOF pulse output on PIN

Bit 19: 18 Reserved

0x0

resd

Kept at its default value.

Bit 17

LP_MODE

0x0

rw

Low-power mode

。

This bit is used to control the OTG PHY consumption.

When this bit is set to 1 by software, the OTG PHY enters
low-power mode; when this bit is cleared by software, the
OTG PHY operates in normal mode.
0: Non-low-power mode

«
...
393
394
395
396
397
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

Vb-C60 - Ptz Network Camera

Brand: Canon Pages: 30

Brand: Jetter Pages: 35

Brand: National Instruments Pages: 5

Brand: National Instruments Pages: 76

Brand: Lanner Pages: 2

Brand: NXP Semiconductors Pages: 24

Storagelibrary T24

Brand: Tandberg Data Pages: 28

InterReach Fusion SingleStar

Brand: LGC wireless Pages: 154

Easy Tool-ID BSG TID-05-T30-00-005

Brand: Balluff Pages: 46

memonizerWORKSTATION

Brand: MEMON Pages: 2

Brand: A4Tech Pages: 8

ELITENAS EN104L+(B)

Brand: Sans Digital Pages: 9

Brand: AMD Pages: 45

Brand: Uctronics Pages: 2

Brand: Omron Pages: 11

PC/104-PCMCIA-1

Brand: Kontron Pages: 20

Brand: Sony Ericsson Pages: 2

Brand: Abov Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands