manualshive.com logo in svg

ARTERY AT32F425 Series, Reference Manual

The ARTERY AT32F425 Series Reference Manual is a comprehensive guide for users to navigate the features and functions of their device. Download the manual for free from our website to access detailed instructions and troubleshooting tips. Ensure optimal performance with the help of this essential resource.

Share
Download
background image

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 407 

 

Ver 2.01

 

endpoint 7. 

20.6.5.7  OTGFS all endpoints interrupt mask register 

(OTGFS_DAINTMSK) 

When an event occurs on a device endpoint, the device endpoint interrupt mask register works with the 
device endpoint interrupt register to interrupt the application. However, the device all endpoints interrupt 
register corresponding to this interrupt is still set. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 24  Reserved 

0x0000 

resd 

Kept at its defaut value. 

Bit 23: 16  OUTEPTMSK 

0x0000 

rw 

OUT EP interrupt mask bits 
One OUT endpoint per bit. Bit 16 for OUT endpoint 0, bit 
18 for OUT endpoint 2.

 

0: Interrupt masked 
1: Interrupt unmasked 

Bit 15: 8 

Reserved 

0x0000 

resd 

Kept at its defaut value. 

Bit 7: 0 

INEPTMSK 

0x0000 

rw 

IN EP interrupt mask bits 
One IN endpoint per bit. Bit 0 for IN endpoint 0, bit 7 for IN 
endpoint 7. 
0: Interrupt masked 
1: Interrupt unmasked 

20.6.5.8  OTGFS device IN endpoint FIFO empty interrupt mask 

register (OTGFS_DIEPEMPMSK) 

This register works witH the TXFE_OTGFS_DIEPINTx register to generate an interrupt. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 8 

Reserved 

0x0000 

resd 

Kept at its defaut value. 

Bit 7: 0 

INEPTXFEMSK 

0x0000 

rw 

IN endpoint Tx FIFO empty interrupt mask bits 
These bits serve as mask bits for the device IN endpoint 
interrupt register. 
A transmit FIFO empty interrupt bit per IN endpint. Bit 0 for 
IN endpoint 0, bit 7 for IN endpoint 7. 
0: Interrupt masked 
1: Interrupt unmasked 

20.6.5.9  OTGFS device control IN endpoint 0 control register 

(OTGFS_DIEPCTL0) 

This section describes the control IN endpoint 0 control register. Nonzero control endpoint uses registers 
for endpoints 1-7. 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31 

EPTENA 

0x0 

rw1s 

Endpoint enable 

– 

The application sets this bit to start data transmission on 
the endpoint 0. 

– 

The controller clears this bit before generating the 
following interrupts: 

– 

Endpoint disabled 

– 

Transfer completed. 

Bit 30 

EPTDIS 

0x0 

ro 

Endpoint disable 
The application sets this bit to stop data transmission on 
an  endpoint.  The  application  must  wait  for  the  endpoint 
disabled interrupt before treating the endpoint as disabled. 
The  controller  clears  this  bit  before  setting  the  endpoint 
disabled  interrupt.  The  application  must  set  this  bit  only 
when the endpoint is enabled. 

Bit 29: 28  Reserved 

0x0 

resd 

Kept at its default value. 

Bit 27 

SNAK 

0x0 

wo 

Set NAK 
A  write  to  this  bit  sets  the  NAK  bit  of  the  endpoint.  The 
application can use this bit to control the transmission of 
NAK handshakes on the endpoint. The controller also sets 
this  bit  when  a  SETUP  data  packet  is  received  on  the 
endpoint. 

Bit 26 

CNAK 

0x0 

wo 

Clear NAK 

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

XMG OASIS Disassembly Procedure preview
OASIS
Brand: XMG Pages: 5
NAD M10 Quick Setup Manual preview
M10
Brand: NAD Pages: 2
3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Brand: Idis Pages: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Brand: Paradyne Pages: 2
ekwb EK-FB GA AX370 Gaming RGB Monoblock Installation Manual preview
EK-FB GA AX370 Gaming RGB Monoblock
Brand: ekwb Pages: 2
Xilica Audio Design XP 4080 User Manual preview
XP 4080
Brand: Xilica Audio Design Pages: 30
IDT DBP 7+4 User Manual preview
DBP 7+4
Brand: IDT Pages: 93
Konica Minolta SRX-101A Operation Manual preview
SRX-101A
Brand: Konica Minolta Pages: 31
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
RR-Concepts StationMaster Manual preview
StationMaster
Brand: RR-Concepts Pages: 12
Omron G3RV-SL500-A Manual preview
G3RV-SL500-A
Brand: Omron Pages: 14
Teridian 71M6533 Quick Start Manual preview
71M6533
Brand: Teridian Pages: 2
Inspired Energy ATA004N Operating Instructions preview
ATA004N
Brand: Inspired Energy Pages: 5
HMS Anybus AWB3000 Startup Manual preview
Anybus AWB3000
Brand: HMS Pages: 18
ICOP Technology VDX-6354RD User Manual preview
VDX-6354RD
Brand: ICOP Technology Pages: 42
Paradyne Hotwire 5620 RTU Installation Instructions Manual preview
Hotwire 5620 RTU
Brand: Paradyne Pages: 20

Brands by name

Popular brands

Load more brands