manualshive.com logo in svg

ARTERY AT32F425 Series, Reference Manual

The ARTERY AT32F425 Series Reference Manual is a comprehensive guide for users to navigate the features and functions of their device. Download the manual for free from our website to access detailed instructions and troubleshooting tips. Ensure optimal performance with the help of this essential resource.

Share
Download
background image

  AT32F425

 

Series  Reference  Manual

 

2022.03.30

 

Page 146 

 

Ver 2.01

 

1: Acknowledge failure 

Bit 3 

ADDRHF 

0x0 

r 

0~7 bit address head match flag 
0: 0~7 bit address head mismatch 
1: 0~7 bit address head match 

Bit 2 

RDBF 

0x0 

r 

Receive data buffer full flag 
0: Data register has not received data yet 
1: Data register has received data 

Bit 1 

TDIS 

0x0 

rw1s 

Transmit data interrupt status 
0: Data has been written to the I2C_TXDT 
1:  Data  has  been  sent  from  the  I2C_TXDT  to  the  shift 
regiter.  I2C_TXDT  become  empty,  and  thus  the  to-be-
transferred data must be written to the I2C_TXDT. 
When the clock stretching mode is disabled, a TDIS event 
is  generated  by  writing  1  so  that  data  is  writtento  the 
I2C_TXDT register in advance. 

Bit 0 

TDBE 

0x0 

rw1s 

Transmit data buffer empty flag 
0: I2C_TXDT not empty 
1: I2C_TXDT empty 
This bit is only used to indicate the current status of the 
I2C_TXDT register. The I2C_TXDT register can be cleared 
by writing 1 through software.   

11.7.8  Status clear register (I2C_CLR) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 14 

Reserved 

0x00000 

res 

Kept at its default value. 

Bit 13

 

ALERTC 

0x0 

w 

Clear SMBus alert flag 
SMBus alert flag is cleared by writing 1. 

Bit 12 

TMOUTC 

0x0 

w 

Clear SMBus timeout flag 
SMBus timeout flag is cleared by writing 1. 

Bit 11 

PECERRC 

0x0 

w 

Clear PEC receive error flag 
PEC receive error flag is cleared by writing 1. 

Bit 10 

OUFC 

0x0 

w 

Clear overload / underload flag 
Overload / underload flag is cleared by writing 1. 

Bit 9 

ARLOSTC 

0x0 

w 

Clear arbitration lost flag 
Arbitration lost flag is cleared by writing 1. 

Bit 8 

BUSERRC 

0x0 

w 

Clear bus error flag 
Bus error flag is cleared by writing 1 

Bit 7: 6 

Reserved 

0x0 

res 

Kept at its default value. 

Bit 5 

STOPC 

0x0 

w 

Clear stop condition generation complete flag 
Stop  condition  generation  complete  flag  is  cleared  by 
writing 1. 

Bit 4 

ACKFAILC 

0x0 

w 

Clear acknowledge failure flag 
Acknowledge failure flag is cleared by writing 1. 

Bit 3 

ADDRC 

0x0 

w 

Clear 0~7 bit address match flag 
0~7 bit address match flag is cleared by writing 1. 

Bit 2: 0 

Reserved 

0x0 

res 

Kept at its default value. 

11.7.9  PEC register (I2C_PEC) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 8 

Reserved 

0x000000 

res 

Kept at its default value. 

Bit 7: 0 

PECVAL[7: 0] 

0x00 

r 

PEC value 

11.7.10 Receive data register (I2C_RXDT) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 8    Reserved 

0x000000 

res 

Kept at its default value. 

Bit 7: 0 

DT[7: 0] 

0x00 

r 

Receive data register 

11.7.11 Transmit data register (I2C_TXDT) 

Bit 

Register 

Reset value 

Type 

Description 

Bit 31: 8    Reserved 

0x000000 

res 

Kept at its default value. 

Bit 7: 0 

DT[7: 0] 

0x00 

rw 

Transmit data register 

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

DAQ system PCIe-FRM13 User Manual preview
PCIe-FRM13
Brand: DAQ system Pages: 41
DAQ system PCIe-SER01 User Manual preview
PCIe-SER01
Brand: DAQ system Pages: 19
Aleratec 310108 Quick Start Manual preview
310108
Brand: Aleratec Pages: 12
Industrex M43ic Instruction Manual preview
M43ic
Brand: Industrex Pages: 51
Multitech MultiConnect SE MTS2EA Quick Start Manual preview
MultiConnect SE MTS2EA
Brand: Multitech Pages: 8
AXIOMTEK eBOX532-100-FL Series Quick Installation Manual preview
eBOX532-100-FL Series
Brand: AXIOMTEK Pages: 2
Ericsson Marconi OMS 1200 Product Description preview
Marconi OMS 1200
Brand: Ericsson Pages: 136
Zhone IMACS Network Device Product Manual preview
IMACS Network Device
Brand: Zhone Pages: 114
QNAP TS-1283XU-RP User Manual preview
TS-1283XU-RP
Brand: QNAP Pages: 54
SAB SABVISION NVR32 Quick Start Manual preview
SABVISION NVR32
Brand: SAB Pages: 29
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Brand: Infoblox Pages: 13
Digital Voice Systems VC-20-MR2 User Manual preview
VC-20-MR2
Brand: Digital Voice Systems Pages: 32
Crown PIP-AF Owner'S Manual preview
PIP-AF
Brand: Crown Pages: 7
SilverStone EXB02 Manual preview
EXB02
Brand: SilverStone Pages: 12
Sun Microsystems UltraSPARC-I User Manual preview
UltraSPARC-I
Brand: Sun Microsystems Pages: 410
HeimVision HM243 User Manual preview
HM243
Brand: HeimVision Pages: 167
ADC The DSX Value Solution (Japanese) LDX154 (Japanese) Brochure preview
The DSX Value Solution (Japanese) LDX154
Brand: ADC Pages: 4
JVC AHA-8920 Before Using preview
AHA-8920
Brand: JVC Pages: 26

Brands by name

Popular brands

Load more brands