ARTERY AT32F425 Series Reference Manual Download Page 392 | Manualshive

Page: 392 / 429

background image

AT32F425

Series Reference Manual

2022.03.30

Page 392

Ver 2.01

set after power-on reset, the application can clear this bit.

Bit 2

OTGINT

0x0

ro

Accesible in both host and device modes
OTG interrupt
The controller sets this bit to indicate that an OTG protocol
event is generated. The application must read the
OTGFS_GOTGINT register to determine the exact source
that caused this interrupt. The application must clear the
corresponding status bit in the OTGFS_GOTGINT register
to clear this bit.

Bit 1

MODEMIS

0x0

rw1c

Accesible in both host and device modes
Mode mismatch interrupt
The  controller  sets  this  bit  when  the  application  is
attempting to access:
A  host-mode  register,  when  the  controller  is  running  in
device mode
A device-mode register, when the controller is running in
host mode
An  OKAY  response  occurs  when  the  register  access  is
completed on the AHB, but it is ignored by the controller
internally,  and  does  not  affect  the  operation  of  the
controller.
This bit can be set by the controller only. The application
must write 1 to clear this bit.

Bit 0

CURMOD

0x0

ro

Accesible in both host and device modes
Current mode of operation
This bit indicates the current mode.
0: Device mode
1: Host mode

20.6.3.7 OTGFS interrupt mask register (OTGFS_GINTMSK)

This register works with the Interrupt Register to interrupt the application. When an interrupt bit is masked,
the interrupt related to this interrupt bit is not generated. However, the Interrupt Register bit
corresponding to this interrupt is still set.
Interrupt mask: 0
Interrupt unmask: 1

Bit

Register

Reset value

Type

Description

Bit 31

WKUPINTMSK

0x0

rw

Accesible in both host and device modes
Resume/Remote wakeup detected interrupt mask

Bit 30

Reserved

0x0

resd

Kept at its default value.

Bit 29

DISCONINTMSK

0x0

rw

Accesible in both host and device modes
Disconnect detected interrupt mask

Bit 28

CONIDSCHGMSK

0x0

rw

Accesible in both host and device modes
Connector ID status change mask

Bit 27

Reserved

0x0

resd

Kept at its default value.

Bit 26

PTXFEMPMSK

0x0

rw

Accesible in host mode only
Periodic TxFIFO empty mask

Bit 25

HCHINTMSK

0x0

rw

Accesible in host mode only
Host channels interrupt mask

Bit 24

PRTINTMSK

0x0

ro

Accesible in host mode only
Host port interrupt mask

Bit 23: 22 Reserved

0x0

resd

Kept at its default value.

Bit 21

INCOMPIPMSK
INCOMPISOOUTMSK

0x0

rw

Incomplete periodic transfer mask
Accesible in host mode only
Incomplete isochronous OUT transfer mask
Accesible in device mode only

Bit 20

INCOMISOINMSK

0x0

rw

Accesible in device mode only
Incomplete isochronous IN transfer mask

Bit 19

OEPTINTMSK

0x0

rw

Accesible in device mode only
OUT endpoints interrupt mask

Bit 18

IEPTINTMSK

0x0

rw

Accesible in device mode only
IN endpoints interrupt mask

Bit 17

Reserved

0x0

rw

Kept at its default value.

«
...
390
391
392
393
394
...
»

Summary of Contents for AT32F425 Series














































































































































































































































































































































































































































Reviews:

No comments

Related manuals for AT32F425 Series

Brand: EAW Pages: 10

SmartMedia Adapter PC Card REX-SMA01F

Brand: Ratoc Systems Pages: 75

Brand: TC Electronic Pages: 55

Brand: Amperes Pages: 8

StorageWorks AIT 35GB AutoLoader

Brand: Compaq Pages: 4

Converter Board R0E521237CFK00

Brand: Renesas Pages: 6

PowerBeam PBE-5AC-400-ISO

Brand: Ubiquiti Pages: 23

Brand: Z-Wave Pages: 42

AirStation G54 WLA2-G54

Brand: Buffalo Pages: 8

Brand: Xcellon Pages: 24

NC-MCO - TECHNICAL

Brand: Crest Audio Pages: 2

Brand: Cypress Semiconductor Pages: 28

MTDOT-868 Series

Brand: Multitech Pages: 60

Brand: Kontron Pages: 14

Safeguard for Privileged Sessions 3000

Brand: One Identity Pages: 37

Brand: VIA Technologies Pages: 2

Brand: Panasonic Pages: 78

Brand: FOR-A Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands