Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 550 / 1812

February 2013
2-526 ColorQube® 9303 Family
OF 1
Status Indicator RAPs
Tray 1 and 2 Assembly
Remove tray 1 and tray 2 and run the following components:
• Enter code dC330 code 71-002 T1 Feed / Elevate Motor, to run the tray 1 feed motor, PL
81.25 Item 22 . The paper tray must be open when the motor is running.
• Enter code dC330 code 72-001 T2 Feed / Elevate Motor, to run the tray 2 feed motor, PL
81.26 Item 22 . The paper tray must be open when the motor is running.
• Open left hand door.
• Enter dC330 code 70-025 3 tray transport motor, to run tray 1 and tray 2 transport rolls,
PL 73.16 Item 3 .
Possible causes and potential solutions are:
• Squeaks.
Possible causes are:
– Contamination of the drive shafts and bearings.
– Incorrectly adjusted or worn drive belts.
– Incorrectly aligned or damaged parts.
Solution:
– Remove and clean the drive shafts, bearings, GP 27 .
– Check 3 tray transport drive belt. Install new parts as necessary, PL 73.16 Item 7 .
– Check for parts that are damaged or out of position.
– Adjust or install new components as necessary.
Tray 3 Assembly
Run the following components:
• Enter dC330 code 73-001 T3 Feed Motor, to operate the tray 3 feed motor, PL 81.30 Item
22 . The paper tray must be open when motor is running.
• Pull out tray 3 and let the tray drop, then push the tray back in.
• Enter dC330 code 73-002 T3 Elevate Motor, to elevate tray 3, PL 73.16 Item 2 . The paper
tray must be open when the motor is running.
• Enter dC330 code 70-025 3 Tray Transport motor to run the 3 tray transport motor, PL
73.16 Item 3 .
Possible causes and potential solutions are:
• No drive or a knocking noise from the 3 tray transport motor.
Possible causes are:
– The 3 tray transport motor, PL 73.16 Item 3 .
– Worn or stretched elevator cables, PL 73.15 Item 17 , PL 73.15 Item 18 , PL 73.15
Item 19 .
Solution:
– Check the drive belt and gears, PL 73.16 .
– Check that the paper trays are correctly positioned and that the tray moves freely
inside the tray assembly.
– Adjust or install new components as necessary.
Bypass Tray 4 Assembly
Run the following components:
• Enter dC330 code 74-420 Bypass Feed Motor, to run the bypass feed motor, PL 74.10
Item 2 .
Possible causes and potential solutions are:
• No drive or a knocking noise from the bypass feed motor.
Possible causes are:
– Incorrectly aligned or damaged parts.
– Contamination of the drive shafts and the bearings.
Solution:
– Check the bypass feed motor, rolls and bearings, PL 73.16 .
– Adjust or install new components as necessary.
Tray 5 Assembly
Run the components as follows:
• Open the tray 5 door to lower the elevator.
• Close the door or actuate the interlock.
• Enter dC330 code 75-019 Tray 5 Elevator Motor Up to drive the tray up, PL 75.68 Item 4 .
• Enter dC330 code 75-020 Tray 5 Elevator Motor Down to drive the tray down.
• Enter dC330 code 75-018 Tray 5 Transport Motor to operate the tray 5 transport motor,
PL 81.40 Item 2 .
• Enter dC330 code 75-117 Tray 5 Feed Motor to operate the tray 5 feed motor, PL 81.40
Item 3 .
Possible causes are:
• Incorrectly aligned or damaged parts.
• Contamination of the drive shafts and the bearings.
Solution:
• Check the motor, rolls, bearings, PL 73.16 . Clean as necessary, GP 27 .
• Adjust or install new components as necessary.
Vertical Paper Path
NOTE: A door cheat for the main door is not required.
Run the components as follows:
• Enter dC330 code 82-001 Vertical Trans Motor Fwd (M2) to run the vertical transport
motor forward, PL 82.10 Item 12 . To diagnose the source of the noise, run the motor with
the upper left door and mid left door closed, then opened.
• Enter dC330 code 82-002 Vertical Trans Motor Rev (M2) to run the vertical transport
motor in reverse.
Possible causes are:
• Incorrectly aligned or damaged parts.
• Contamination of the drive shafts, idler rolls or bearings.
Solution:
• Check the motor, rolls, bearings, and drive belts, PL 82.10 . Clean as necessary, GP 27 .
• Check the idler rolls in the upper left door assembly, PL 70.30 . Clean as necessary, GP
27 .
• Check the bearings on the end of the transport roller drive 2, PL 82.10 Item 1 and the
transport roller TAR vertical, PL 82.10 Item 2 . Clean as necessary, GP 27 .
• Adjust or install new components as necessary.