Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 419 / 1812

February 2013
2-395 ColorQube® 9303 Family
91-698-00, 91-699-00, 91-706-00, 91-712-00, 91-718-
Status Indicator RAPs
MOT91-034 runs and the lower carriage moves left or right.
Y
N
Refer to
WD 9.11, check MOT91-034.
Check the wiring between PJ303 on the marking unit driver PWB and MOT91-
034.
Refer to:
•
GP 10 How to Check a Motor.
• 01H +24V Power Distribution RAP.
• 01J +50V Power Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary.
• X-axis drive motor lower, PL 91.25 Item 5 .
• Marking unit driver PWB, PL 92.10 Item 4 .
Perform the following:
1. Inspect the docking pins and docking surfaces for debris that could prevent the
carriage from fully docking. Clean the docking pins and surfaces as necessary,
GP 27 .
2. Move the marking unit back into the operational position, refer to GP 6 .
3. Observe the carriage as it moves into the docked position.
To do this enter the Diagnostic tab and select dC612 Print Test Patterns. Select
TP 16 , Stitch Identification Test Pages. The carriage will move into the docked
position to enable printing.
The carriage docks correctly against the drum.
Y
N
Inspect the marking unit drive system for broken or bound linkages. Install new
components necessary.
PL 91.10 .
Check the fault history, dC122 .
If fault codes 91-712-00 and 91-720-00 are listed install a new upper carriage
assembly,
PL 91.20 Item 1 .
If fault codes 91-706-00 and 91-732-00 are listed install a new lower carriage assem-
bly,
PL 91.25 Item 1 .
If the fault is intermittent. Check the area surrounding the carriage and umbilicals for
wiring damage or obstructions. Repair the harness,
REP 1.1 as necessary.
Go to the appropriate RAP.
Enter dC612 and print TP 16, Stitch Identification Test Pages and check that the print quality is
good.
Perform
SCP 5 Final Actions
91-721-00, 91-722-00, 91-735-00, 91-736-00 IOD
Contamination Error RAP
91-721-00 IOD calibration.
91-722-00 IOD calibration 2D.
91-735-00 IOD non-static scanbar artifact.
91-736-00 IOD static scanbar artifact.
Procedure
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
WARNING
Take care during this procedure. The drum will become hot during normal operation.
CAUTION
Do not connect the harness to the IOD PWB with the machine powered on. This may damage
the IOD sensor.
CAUTION
Use care when working near the drum. The drum can be damaged easily, which will cause
print quality defects.
CAUTION
Do not disconnect and reconnect the flex cables at the IOD PWB. the flex cables are easily
damaged. The cable must only be handled in the area of the blue backer.
Perform dC969 Cleaning Ink Smears. Check the prints. The prints are clean.
Y N
Repeat
dC969 until the prints are clean.
Perform dC971 Head to Head Alignment. The routine completes successfully.
Y N
Enter
dC330 and select 94-009 Drum Drive Slew Speed. Select start and inspect the
drum for contamination as it rotates. The drum is clean.
Y
N
Clean the drum,
GP 27 .
Clean the IOD, GP 27 .
Check the wire routing under the IOD for abrasions. Repair the harness, REP 1.1 as neces-
sary. If the fault remains, install new components as necessary:
• IOD assembly, PL 94.15 Item 1 .
• Drum driver PWB, PL 1.15 Item 4 .
A B D