Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 400 / 1812

February 2013
2-376 ColorQube® 9303 Family
91-572-00, 91-573-00, 91-575-00
Status Indicator RAPs
91-572-00, 91-573-00, 91-575-00 Wiper Vertical Error RAP
91-572-00 Printhead wiper vertical motion edge not found.
91-573-00 The wiper encountered an unexpected event while in vertical motion.
91-575-00 The vertical wiper could not complete the requested motion.
NOTE: Invalid move errors are typically the result of mechanisms being moved manually
instead of under machine control.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
CAUTION
Do not handle or attempt to clean the wiper blade. Wiper blade contamination can damage the
printheads.
CAUTION
Do not touch the exposed face of the printheads. Surface contamination or minor damage can
destroy the printhead. Printheads must only be cleaned by a purge cycle.
CAUTION
Use care when opening the marking unit drawer when hot. Ink can spill from the ink reservoir
located at the back of the drawer if opened with too much force. Ink cross-color contamination
could also occur.
• Check the HM tension spring is connected, Figure 1 . If necessary install a new spring, PL
91.15 Item 14 .
• Check that the wiper is level. Refer to the Replacement procedure in REP 91.3 .
• Check HM wiper, PL 91.15 Item 13 for full travel.
• Check for damage or debris that restricts wiper movement.
Procedure
Cheat the front door interlock. Open the marking unit drawer, GP 6 to observe wiper motion.
Enter dC330 code 91-023 to run the HM vertical motion motor, MOT91-023, Figure 1 .
NOTE: The HM vertical motion motor will run a complete cycle.
MOT91-023 runs.
Y
N
Go to
WD 9.11 . Check MOT91-023.
Refer to:
•
GP 10 How to Check a Motor.
• PJ401, Marking Unit Driver PWB .
• 01H +24V Power Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
•
HM vertical motion motor, PL 91.15 Item 12 .
• Marking unit driver PWB, PL 92.10 Item 4 .
Enter dC330 code 91-014 to test the HM position sensor, Q91-014. Actuate Q91-014. The
display changes.
Y
N
Go to
WD 9.11 . Check S91-014.
Refer to:
•
GP 13 How to Check a Switch.
• PJ304, Marking Unit Driver PWB .
• 01B +3.3V ESTAR Power Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
•
HM position sensor, PL 91.15 Item 17 .
• Marking unit driver PWB, PL 92.10 Item 4 .
Check the area surrounding the carriage, wiper assembly, and umbilicals for wiring damage or
obstructions that prevent carriage or wiper movement. The wiring is good.
Y
N
Install new wiring or repair,
REP 1.1 as necessary.
Go to WD 9.11 . Check all connections:
• PJ401, PJ304, Marking Unit Driver PWB .
If necessary, install a new marking unit driver PWB, PL 92.10 Item 4 .
Figure 1 Component location
HM vertical motion
motor, MOT91-023
HM position sensor,
Q91-014
Check the springs are connected and
the belts are tensioned.(Front and
rear.)
A
A