Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 340 / 1812

February 2013
2-316 ColorQube® 9303 Family
73-215-00
Status Indicator RAPs
73-215-00 Tray 3 Hoist Failure RAP
73-215-00 Tray 3 hoist failure.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check for obstructions behind the tray.
• Ensure that the tray is pushed fully home.
• Check that the tray elevator cables and mechanisms are located correctly. Refer to REP
73.3 .
• If the tray only elevates up by 25 mm (1 inch) and stops. Go to 73A RAP and check the
tray empty actuator.
Procedure
Enter dC330 code 73-303 tray 3 home sensor, Q73-303, PL 73.16 Item 8 . Press Start. Pull out
the tray. The display changes.
Y
N
Refer to
WD 7.4 . Check tray 3 home sensor, Q73-303. Refer to:
• GP 11 How to Check a Sensor.
• PJ954, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 home sensor, PL 73.16 Item 8 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 73-383 tray 3 stack height sensor, Q73-383, PL 81.30 Item 17 . Press Start.
Pull out tray 3. Manually actuate the stack height sensor. The display changes.
Y
N
Refer to
WD 7.4 . Check tray 3 stack height sensor, Q73-383. Refer to:
• GP 11 How to Check a Sensor.
• PJ953, 3 tray module PWB.
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 stack height sensor, PL 81.30 Item 17 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 73-002 tray 3 elevator motor, MOT73-002, PL 73.16 Item 2 . Pull out tray 3.
Press Start. The motor runs.
Y N
Refer to
WD 7.5 . Check that the tray 3 limit switch, PL 81.30 Item 25 , is not actuated.
While not actuated, check for +24V at both contacts on the switch. Refer to:
• GP 13 How to Check a Switch.
• PJ957, 3 tray module PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 limit switch, PL 81.30 Item 25 .
• 3 tray module PWB, PL 73.16 Item 4 .
Refer to WD 7.5 . Check tray 3 elevator motor, MOT73-002. Refer to:
• GP 10 How to Check a Motor.
• PJ957, 3 tray module PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 elevator motor, PL 73.16 Item 2 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Perform the following:
•
Check elevator cables, PL 73.15 .
• Check elevator motor drive coupling, PL 73.16 Item 2 .
• Check tray elevator drive gears and drive coupling, PL 73.15 Item 11 .
If the fault still occurs, then go to 73A Tray 3 Out of Paper RAP.