Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 112 / 1812

February 2013
2-88 ColorQube® 9303 Family
12-340-00-110, 12-341-00-110, 12-342-00-110
Status Indicator RAPs
12-340-00-110, 12-341-00-110, 12-342-00-110 Ejector
Movement Failure RAP
12-340-00-110 The ejector is not at the home position.
12-341-00-110 The ejector is not at the out position.
12-342-00-110 The ejector fails to perform a cycle of operation.
NOTE: A cycle of operation for the ejector is to cycle from the home position to the out position
and back to the home position.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
WARNING
Take care not to topple the LCSS. The LCSS is unstable when undocked from the
machine. Do not show the customer how to undock the LCSS.
• Check the LCSS PWB DIP switch settings, refer to 12F-110 LCSS PWB DIP Switch Set-
tings RAP.
• Un-dock the LCSS, REP 12.13-110 , Check for any obstructions that would prevent the
ejector from moving. Cheat the docking interlock switch.
Procedure
NOTE: All LCSS interlocks must be made to 24V to the motors.
NOTE: With reference to WD 12.1 component control codes;
Code 12-234 moves the ejector assembly to the home position.
Code 12-235 moves the ejector assembly to the out position.
Code 12-236 cycles the ejector until time-out.
Enter dC330 code 12-185, actuate the ejector out sensor Q12-185, PL 12.50 Item 3 . The dis-
play changes.
Y
N
Go to
WD 12.1 . Check Q12-185.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 11 How to Check a Sensor.
• P/J304, LCSS PWB .
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Ejector out sensor, PL 12.50 Item 3 .
• LCSS PWB, PL 12.75 Item 1 .
Enter dC330 code 12-184, actuate the ejector home sensor Q12-184, PL 12.50 Item 3 . The
display changes.
Y
N
Go to
WD 12.1 . Check Q12-184.
Refer to:
• 12G-110 LCSS PWB Damage RAP.
• GP 11 How to Check a Sensor.
• P/J304, LCSS PWB .
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Ejector home sensor, PL 12.50 Item 3 .
• LCSS PWB, PL 12.75 Item 1 .
Enter dC330 code 12-236 to check the movement of the ejector, PL 12.50 Item 1 . The ejec-
tor motor cycles.
Y
N
Check that the large tie-wrap around the motor of the ejector assembly has not cut
through the motor wires and caused a short circuit to the case of the motor. If necessary
cut the tie-wrap, then tape and isolate the wires. The ejector motor cycles.
Y
N
Go to
WD 12.1 . Check the ejector motor home MOT12-234.
Refer to:
•
12G-110 LCSS PWB Damage RAP.
• GP 10 , How to Check a Motor.
• P/J303, LCSS PWB .
• 12D-110 LCSS Power Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
•
Ejector assembly, PL 12.50 Item 1 .
• LCSS PWB, PL 12.75 Item 1 .
The ejector cycles noisily, colliding with the end stops.
Y
N
Check the stapler to ensure the staples are correctly formed. Mis-formed staples can
cause the set to hang in the stapler causing ejector movement failures. The staples are
correctly formed.
Y
N
Clear the staple head of any mis-formed staples, then check the operation of the sta-
pler. If necessary, install a new staple head unit,
PL 12.55 Item 5 .
If the ejector is still not moving, install a new ejector assembly, PL 12.50 Item 1 .
Perform SCP 5 Final Actions.
Go to WD 12.1 . +5v is available at P/J 304 between pins 7 and 8.
Y N
Go to the
12D-110 LCSS Power Distribution RAP and 01L 0V Distribution RAP.
Connect a service meter at P/J 304 between pins 8 and 9. Slowly rotate the ejector motor
encoder. The voltage changes b5V and 0V.
Y
N
Go to
WD 12.1 . Check the wiring and connectors between the ejector motor encoder sen-
sor and the LCSS PWB. If necessary repair the wiring, REP 1.1 . If the wiring is good,
install a new ejector motor encoder sensor, PL 12.50 Item 3 .
Perform the 12G-110 LCSS PWB Damage RAP. If necessary install a new LCSS PWB, PL
12.75 Item 1 .
A
A