Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 504 / 1812

February 2013
2-480 ColorQube® 9303 Family
99-180-00 to 99-217-00
Status Indicator RAPs
99-180-00 to 99-217-00 PEST Error 5 RAP
99-180-00 Board link 3TM safe mode.
99-185-00 Board link PFP safe mode.
99-210-00 Power, drum driver board ADC ref to 3.3V / out of range.
99-211-00 Power DDB ADC ref to 24V out of range.
99-212-00 Power 24V base above max.
99-213-00 Power 24V base below min.
99-214-00 Power 24V base not stable.
99-215-00 Power DDB ADC 50V APG out of range.
99-216-00 Power 50V base above max.
99-217-00 Power 50V base below min.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
Procedure
Refer to Table 1 . Perform the relevant action. For an explanation of PEST codes refer to
dC123 .
Table 1 PEST Hard and Soft Fault Codes
Code Hard/Soft Action
99-180 Hard Safe mode indicates a firm ware mismatch. Check IME code ver-
sion vs. 3TM PLD version and upgrade or revert as appropriate. If
problem continues install a new 3 Trays module PWB,
PL 73.16
Item 4 .
99-185 Hard Safe mode indicates a firm ware mismatch. Check IME code ver-
sion vs. tray 5 PLD version and upgrade or revert as appropriate.
If problem continues install a new tray 5 control PWB,
PL 75.68
Item 8 .
99-210 Soft Go to the 01B RAP.
99-211 Soft Go to the 01H RAP.
99-212 Soft Switch off the machine, GP 14 . Check all 24V devices for heat or
noise and the harnesses for damage or short circuits (i.e. chaff-
ing). If a 24V component has been replaced then check that har-
ness first.
To isolate 5 major areas:
1.
Unplug all drum driver PWB connectors except PJ602,
PJ603 and PJ 902.
If the fault 99-212 is removed but other 99-xxx errors occur,
Then check all 24V components and harnesses to the drum
driver PWB.
2. Unplug all media path driver PWB connectors except PJ803,
PJ408 and PJ 402.
If the fault 99-212 is removed but other 99-xxx errors occur,
Then check all 24V components and harnesses to the media
path driver PWB.
3. Unplug all marking unit driver PWB connectors except
PJ203.
If the fault 99-212 is removed but other 99-xxx errors occur,
Then check all 24V components and harnesses to the mark-
ing unit driver PWB.
4. Remove power to the quad wave amp PWB, by disconnect-
ing PJ101 on the IME controller PWB.
If the fault 99-212 is removed and no 99 errors occur, but a
91-610 error occurrs.Then check all 24V components and
harnesses to the quad wave amp PWB.
5. Remove power to the CBC tray by disconnecting PJ1 on the
power distribution PWB.
If the fault 99-212 is removed and replaced by a soft error 99-
213. Then check all 24V components and harnesses.
If none of those solve the problem, then try disconnecting the
printhead connectors from the IME controller PWB. This will also
raise head link errors so check for both.
The error could be internal to one of the PWB’s, refer to the
01H
RAP.
99-213 Soft Go to the 01H RAP.
99-214 Soft Go to the 01H RAP.
99-215 Soft Go to the 01J RAP and the 01K RAP.
Table 1 PEST Hard and Soft Fault Codes
Code Hard/Soft Action