Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 352 / 1812

February 2013
2-328 ColorQube® 9303 Family
82-125-00 to 82-133-00, 82-153-00, 82-160-00, 82-162-
Status Indicator RAPs
82-125-00 to 82-133-00, 82-153-00, 82-160-00, 82-162-00,
82-163-00 Confirm Sensor (16) RAP
82-125-00 The sheet has arrived at the confirm sensor (16) too early.
82-126-00 The confirm sensor (16) has detected the sheet was too long. The machine will auto
purge the media path.
82-127-00 The confirm sensor (16) has detected the sheet was too short. The machine will
auto purge the media path.
82-128-00 The confirm sensor (16) has detected a sheet mismatch, the sheet was too long.
82-129-00 The confirm sensor (16) has detected a sheet mismatch, the sheet was too short.
82-130-00 Lead edge late to the confirm sensor (16) from the tree tray module.
82-131-00 Trail edge late at the confirm sensor (16).
82-153-00 The sheet has arrived at the confirm sensor (16) too early.
82-160-00 MP MP2 stall bridged sheet zone 2
82-162-00 The confirm sensor (16) has detected the sheet was too long. The machine will not
auto purge the media path.
82-163-00 The confirm sensor (16) has detected the sheet was too short. The machine will not
auto purge the media path.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check the paper stack in the tray.
• Check that the tray guides are against the edges of the paper.
• Check that the tray is pushed fully home.
• Check for obstructions in the paper path.
• Check that the upper and mid left doors are fully latched.
• If a 82-130-00 fault occurs when feeding from the bypass tray. Check the bypass feed roll
assembly,
PL 74.10 Item 14 .
Procedure
Enter dC330 code 82-125 confirm sensor (16), Q82-125. Press Start. Open the upper left door
then manually actuate the sensor. The display changes.
Y
N
Go to
WD 8.1 . Check the confirm sensor (16), Q82-125. Refer to:
• GP 11 How to Check a Sensor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Confirm sensor (16), PL 82.10 Item 7 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-001 vertical transport motor (M2), MOT82-001. Press Start. The motor
runs.
Y
N
Go to
WD 8.1 . Check the vertical transport motor (M2), MOT82-001. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical transport motor (M2), PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
The vertical transport rolls rotate.
Y
N
Check the drive belt and drive gears on the vertical transport,
PL 82.10 .
If necessary, install new components:
• Transport rolls, PL 82.10 .
• Drive belts, PL 82.10 .
• Drive gears, PL 82.10 .
Enter dC140 Analog Monitor. Select 82-100 vertical transport motor encoder (M2). Press Start.
The number of ticks (i.e. 36 ticks) will flash on the display and then return to show 0 ticks.
Repeat by selecting stop and then start on the popup menu, the number only remains for a few
seconds. The number of ticks is displayed.
Y
N
Go to
WD 8.1 . Check the vertical transport motor (M2), MOT82-001. Refer to:
• GP 10 How to Check a Motor.
• PJ104, Media path driver PWB .
• 01D +5V Distribution RAP.
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Vertical transport motor (M2), PL 82.10 Item 12 .
• Media path driver PWB, PL 1.15 Item 5 .
Check the following:
•
Check the wiring for damage and correct harness routing to the vertical paper path.
• The bearing, shaft and rolls on the transport roll assembly, PL 82.10 ,
• The idler rolls in the upper left side door, PL 70.30 Item 4 .
• The transport rolls for wear, PL 82.10 Item 1 , PL 82.10 Item 2 .
Install new components as necessary.
A
A