Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 538 / 1812

February 2013
2-514 ColorQube® 9303 Family
99-839-00 to 99-871-00
Status Indicator RAPs
99-840 Hard Refer to WD 9.9 . Check the DC cabling to the X axis drive motor upper.
Measure the resistance at PJ102 on the marking unit driver PWB for an
open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the X axis drive motor
upper. If a short is measured, the marking unit driver PWB may be dam-
aged and be reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, X axis drive motor upper,
PL
91.20 Item 5 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP.
Check the upper X axis drive motor.
99-841 Hard Refer to WD 9.9 . Check the DC cabling to the X axis drive motor upper.
Measure the resistance at PJ102 on the marking unit driver PWB for an
open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the X axis drive motor
upper. If a short is measured, the marking unit driver PWB may be dam-
aged and be reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, X axis drive motor upper,
PL
91.20 Item 5 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP.
Check the upper X axis drive motor.
99-842 Soft Go to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP. Check
the upper X axis drive motor.
99-843 Soft Go to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP. Check
the upper X axis drive motor.
99-845 Hard Refer to WD 9.11 . Check the DC cabling to the X axis drive motor lower.
Measure the resistance at PJ303 on the marking unit driver PWB for an
open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the X axis drive motor
lower. If a short is measured, the marking unit driver PWB may be dam-
aged and be reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, X axis drive motor lower,
PL
91.25 Item 5 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP.
Check the lower X axis drive motor.
99-846 Hard Refer to WD 9.11 . Check the DC cabling to the X axis drive motor lower.
Measure the resistance at PJ303 on the marking unit driver PWB for an
open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the X axis drive motor
lower. If a short is measured, the marking unit driver PWB may be dam-
aged and be reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, X axis drive motor lower,
PL
91.25 Item 5 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP.
Check the lower X axis drive motor.
Table 1 PEST codes and action
Code Hard/Soft Action
99-847 Soft Go to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP. Check
the lower X axis drive motor.
99-848 Soft Go to the 91-510-00, 91-511-00 X Axis Motor Over Current RAP. Check
the lower X axis drive motor.
99-860 Hard Refer to WD 9.22 . Check the DC cabling to the IOD shuttle motor. Mea-
sure the resistance at PJ660 on the IOD pre-amplifier PWB for an open
or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the IOD shuttle motor. If a
short is measured, the IOD pre-amplifier PWB may be damaged and be
reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, IOD assembly,
PL 94.15 Item 1 .
Refer to the 91-513-00, 91-514-00, 91-581-00, 91-583-00 IOD Drive
Error RAP. Check the IOD shuttle motor.
99-861 Hard Refer to WD 9.22 . Check the DC cabling to the IOD shuttle motor. Mea-
sure the resistance at PJ660 on the IOD pre-amplifier PWB for an open
or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the IOD shuttle motor. If a
short is measured, the IOD pre-amplifier PWB may be damaged and be
reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, IOD assembly,
PL 94.15 Item 1 .
Refer to the 91-513-00, 91-514-00, 91-581-00, 91-583-00 IOD Drive
Error RAP. Check the IOD shuttle motor.
99-863 Soft Go to the 91-513-00, 91-514-00, 91-581-00, 91-583-00 IOD Drive Error
RAP. Check the IOD shuttle motor.
99-864 Soft Go to the 91-513-00, 91-514-00, 91-581-00, 91-583-00 IOD Drive Error
RAP. Check the IOD shuttle motor.
99-870 Soft Go to the 93-825-00, 93-892-00 Ink Key Plate Motor Over Current RAP.
Check the ink key plate motor.
99-871 Hard Refer to WD 8.4 . Check the DC cabling to the ink key plate motor. Mea-
sure the resistance at PJ406 on the media path driver PWB for an open
or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the ink key plate motor. If a
short is measured, the media path driver PWB may be damaged and be
reported as an ‘open’ error.
If short error is reported, the motor is drawing excessive power.
Install new components as necessary, ink key plate motor,
PL 93.10
Item 14 , media path driver PWB, PL 1.15 Item 5 .
Refer to the 93-825-00, 93-892-00 Ink Key Plate Motor Over Current
RAP. Check the ink key plate motor.
Table 1 PEST codes and action
Code Hard/Soft Action