Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 553 / 1812

February 2013
2-529 ColorQube® 9303 Family
OF 1
Status Indicator RAPs
Possible causes are:
– The LCSS is not aligned correctly.
Solution:
– Check the machine to LCSS alignment, ADJ 12.2-110 .
– Adjust or install new components as necessary.
• Clicking Noise from the LCSS
Possible causes are:
– The staple head continually operating for approximately 15 seconds. This occurs
every time the LCSS top cover or front door is opened then closed, because the sta-
pler is attempting to prime the staple head, by indexing the staple stick forward and
pre-forming two staples.
Solution:
– Check the staple cartridge for jammed staples and remove any that are found.
– Ensure the staple cartridge is fully seated.
– Ensure that the correct staple cartridge is installed.
– Perform 12L-110 Stapling Failure RAP.
HVF / HVF BM
Run the following components:
CAUTION
Ensure that the first tamper in the compiler carriage is returned to the home position before the
second tamper is checked in diagnostics.
• Enter dC330 code 12-223 Transport Motor 1, to run the input transport roll, PL 12.120
Item 2 .
• Enter dC330 code 12-224 Transport Motor 2, to run the exit drive shafts to feed paper to
the top tray or to the stacker tray, PL 12.120 Item 1 .
• Enter dC330 code 12-226 Front Tamper Motor Home, to move the front tamper to the
home position PL 12.125 Item 6 .
• Enter dC330 code 12-227 Rear Tamper Motor Home, to move the rear tamper to the
home position, PL 12.125 Item 6 .
• Enter dC330 code 12-228 Front Tamper Motor Move, to move the front tamper to the cen-
tre of the compiler, PL 12.125 Item 6
• Enter dC330 code 12-229 Rear Tamper Motor Move, to move the rear tamper to the cen-
tre of the compiler tray, PL 12.125 Item 6 .
• Enter dC330 code 12-238 Paddle Roll Motor Run, to lift the paddle unit and rotate the
paddle rolls, PL 12.115 Item 2 .
• Enter dC330 code 12-237 Paddle Motor Home, to lift the paddle unit to the up position, PL
12.115 Item 2 .
• Enter dC330 code 12-241 Bin 1 Elevator Motor Home, to move Bin 1 up to the home posi-
tion, PL 12.105 Item 10 .
• Enter dC330 code 12-242 Bin 1 Elevator Motor Cycle, to move Bin 1 up / down until time
out or stop, PL 12.105 Item 10 .
• Enter dC330 code 12-249 SU1 Motor Fwd, to move the stapler unit to the front, PL 12.110
Item 12 .
• Enter dC330 code 12-248 SU1 Motor Rev Home, to move the stapler unit to the rear, PL
12.110 Item 12 .
• Enter dC330 code 12-250 SU1 Motor Cycle, to run the stapler unit cycle routine, PL
12.110 Item 12 .
• Enter dC330 code 12-251 BM Compiler Motor, runs the compiler BM entry roll, PL 12.175
Item 1 .
NOTE: The tray moves down for 15 seconds and then stops.
• Enter dC330 code 12-252 BM Crease Blade Motor, to move crease blade assembly, PL
12.175 Item 8 .
• Enter dC330 code 12-273 BM Crease Roll Gate Motor, to move the crease blade assem-
bly, PL 12.175 Item 8 and the crease roll gate, PL 12.180 Item 19 .
• Enter dC330 code 12-253 BM Crease Roll Motor, to rotate the two crease rolls, PL 12.175
Item 12 .
• Enter dC330 code 12-255 BM Back Stop Motor, to move the back stop assembly, PL
12.160 , PL 12.165 .
• Enter dC330 code 12-256 BM Tamper 1 Motor, to move the tamper rack and fingers, PL
12.155 Item 3 .
• Enter dC330 code 12-274 BM Conveyor Drive motor, to run the output tray conveyor
belts, PL 12.190 Item 4 .
• Enter dC330 code 12-271 BM flapper Motor, to run the BM flapper, PL 12.175 Item 1 .
• Enter dC330 code 12-273 BM Crease Roll Gate Motor, to move the crease roll gate up
and down, PL 12.180 Item 19 .
• Enter dC330 code 12-261 Inserter Motor, to run inserter main drives, PL 12.315 Item 1 .
• Enter dC330 code 12-253 BM Crease Roll Motor, to run the tri-roller drives, PL 12.175
Item 12 .
• Enter dC330 code 12-269 Clutch Drive, to engage the HVF clutch drive to drive tri-folding
rolls, PL 12.175 Item 12 .
Possible causes and potential solutions are:
• Noise from the right hand side of the machine.
Possible causes are:
– The HVF BM is not aligned correctly.
– Bin 1 not aligned correctly on the main drive belts, PL 12.105 Item 6 .
Solution:
– Check the machine to HVF BM alignment, ADJ 12.1-171 .
– Check that the Bin 1 is level, refer to REP 12.38-171 HVF Stacker Drive Belts.
– Adjust the components if appropriate.
– Install new parts as necessary.
• Knocking.
Possible causes are:
– Mis-adjusted or worn drive belts. PL 12.120 .
– The support fingers on the ejector hit bin1 each time they are moved out.
Solution:
– Adjust the belt tension as required.
– Pre-load bin 1 with 30 sheets of paper this acts a a damper and will stop the noise.
– Install new parts as necessary.
• Squeak.