Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 465 / 1812

February 2013
2-441 ColorQube® 9303 Family
93-549-00 to 93-552-00 and 93-557-00 to 93-560-00
Status Indicator RAPs
• Install a new purge line, PL 91.25 Item 11 .
• If the ink contamination has reached the ink reservoir through the purge line, install a
new ink reservoir,
PL 93.10 Item 10 .
Go to WD 9.6 , WD 9.7 , WD 9.20 , WD 9.21 . Check the ribbon cables between the printheads
and the IME Controller PWB. Refer to:
• P/J101, P/J301, Printhead PWB
• P/J902, P/J904 IME controller PWB
The ribbon cables are good.
Y
N
Re-seat the ribbon cables or install new cables,
PL 92.10 .
Check that the level sense connection at PJ601 on the Printhead PWB is in good condition and
is properly and securely connected. The connection is good.
Y
N
As necessary, install new components:
•
Print head, PL 91.20 Item 2 , PL 91.25 Item 2 .
Disconnect the air hose between the lower and upper purge hoses on the ink reservoir, Figure
2 .
Enter dC330 and stack the code 93-050 to run the reservoir pump MOT93-050, PL 93.10 Item
11 and code 91-045 low pressure assist valve SOL 91.045, PL 93.10 Item 15 . The pump will
run for approximately 10 seconds. If the pump runs, then the air pressure from the discon-
nected air hose is sufficient to feel on the skin, or partially inflate a rubber glove. The pump
runs
Y
N
Go to
WD 9.14 . Check the connection from the solenoid patch PWB to the reservoir pump
motor (MOT93-050) at PJ130.
Go to
WD 9.14 and WD 9.12 . Check the ink reservoir pump motor.
Refer to:
• GP 10 , How to Check a Motor.
• P/J130, Solenoid patch PWB .
• P/J801, Marking unit driver PWB
• 01E +12V Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Marking unit driver PWB, PL 92.10 Item 4 .
• Ink Reservoir, PL 93.10 Item 10 .
Reconnect the air hose from the pump to the ink reservoir, Figure 2 .
Enter the correct dC330 output code to check the ink reservoir solenoids associated with the
fault code:
•
Purge solenoid valve 3, SOL93-061.
• Purge solenoid valve 4, SOL93-062.
• Black ink solenoid valve 5, SOL93-063.
• Black ink solenoid valve 7, SOL93-065.
• Yellow ink solenoid valve 11, SOL93-069.
• Yellow ink solenoid valve 12, SOL93-070.
• Cyan ink solenoid valve 15, SOL93-073.
• Cyan ink solenoid valve 16, SOL93-074.
• Magenta ink solenoid valve 17, SOL93-075.
• Magenta ink solenoid valve 19, SOL93-077.
All solenoids energize
Y
N
Go to
WD 9.14 , WD 9.15 and WD 9.12 . Check the ink reservoir solenoids.
Refer to:
• GP 12 , How to Check a Solenoid.
• P/J430, P/J110, P/J410, P/J610, P/J810 Solenoid patch PWB .
• P/J801, Marking unit driver PWB
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP
Install new components as necessary:
• Ink Reservoir, PL 93.10 Item 10 .
• Marking unit driver PWB, PL 92.10 Item 4 .
Switch off the machine then switch on the machine GP 14 . Allow the printheads to try and
recover. The fault is cleared
Y
N
Install a new ink reservoir
PL 93.10 Item 10 .
Before installing a new ink reservoir. Check that the 4 screws securing the solenoid patch
PWB are not loose. If necessary tighten but do not overtighten the screws. Check that the
check valves on the umbilicals are securely fixed to the umbilicals,
PL 91.25 Item 19 . If
the clips are damaged, install a new umbilical, PL 91.25 Item 20 . The fault is still
present.
Y
N
Perform
dC972 Printhead Uniformity.
Install new components;
1. Install the relevant new printhead PL 91.25 Item 2 .
2. Install a new IME controller PWB, PL 92.10 Item 1 .
Perform SCP 5 Final Actions.
A