Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 551 / 1812

February 2013
2-527 ColorQube® 9303 Family
OF 1
Status Indicator RAPs
Horizontal Paper Path
Run the following components:
• Enter dC330 code 82-003 Horizontal Trans Motor Fwd (M6), to run the horizontal trans-
port motor forward, PL 82.15 Item 9 . To diagnose the source of the noise, run the motor
with the horizontal paper path (handle 4b) closed, then opened.
• Enter dC330 code 82-004 Horizontal Trans Motor Rev (M6), to run the horizontal trans-
port motor in reverse.
Possible causes are:
• Incorrectly aligned or damaged parts.
• Contamination of the drive shafts, idler rolls or bearings.
Solution:
• Check the motor, takeaway rolls, bearings, and drive belts, PL 82.15 . Clean as necessary,
GP 27 .
• Check the idler rolls in the horizontal paper path assembly, PL 82.15 . Clean as necessary,
GP 27 .
• Adjust or install new components as necessary.
Exit Paper Path
Run the following components:
• Enter dC330 code 10-018 Post Transfix Motor (M4) to run the post-transfix motor forward,
PL 10.10 Item 5 .
• Enter dC330 code 83-001 Exit Motor Fwd (M5) to run the exit motor forward, PL 10.15
Item 11 .
• Enter dC330 code 83-002 Exit Motor Rev (M5) to run the exit motor in reverse. Used for
duplex and paper invert.
Possible causes:
• Post-transfix motor (M4), PL 10.10 Item 5 .
• Exit motor (M5), PL 10.15 Item 11 .
• Gear drive, PL 10.10 Item 13 .
• Idlers in stripper gate and baffle assembly, PL 10.12 Item 1 .
Solution:
• Enter dC330 code 10-025 Strip Gate Unlatch and open the stripper gate and baffle
assembly, PL 10.12 Item 1 .
• Stack the code 10-018 Post Transfix Motor (M4) to run the post-transfix motor forward, PL
10.10 Item 5 .
• If the noise repeats, the source is the M4 motor or gear assembly. Install new parts as
necessary.
• If the noise does not repeat, the source is one of the idlers in the stripper gate and baffle
assembly,
PL 10.12 .
• Close stripper gate and baffle assembly.
• Enter dC330 code 10-023 Strip Gate Latch.
If the noise repeats perform the following:
• Open horizontal paper path assembly, PL 82.15 Item 1 .
• If the noise repeats, the source is the M5 motor, idlers or gear assembly, PL 10.15 . Adjust
or install new components as necessary.
• If the noise does not repeat, the source is the exit paper path, PL 10.15 Item 19 . Adjust or
install new components as necessary.
Registration / pre-heat Assembly
NOTE: A door cheat for the main door is not required.
Run the following components:
• Enter dC330 code 89-007 Registration Motor A1 to run registration motor A1, PL 88.11
Item 8 .
• Enter dC330 code 89-008 Registration Motor A2 to run registration motor A2, PL 88.11
Item 8 .
Possible causes:
• Registration motor A1 and A2, PL 88.11 Item 8 .
• Incorrectly adjusted of worn drive belts, PL 88.11 Item 4 .
Solution:
• Clean contamination on the drive shafts and the bearings
• Adjust or install new components as necessary.
If the noise repeats perform the following:
• Enter dC330 code 89-011 Nip A: Open to disengage all of the registration/ pre-heat
Assembly idlers, PL 88.10 Item 20 .
• Enter dC330 code 89-012 Nip A: Narrow to engage idlers 3 and 4, PL 88.10 Item 20 .
• Enter dC330 code 89-013 Nip A: Medium to engage idlers 2 and 5, PL 88.10 Item 20 .
• Enter dC330 code 89-014 Nip A: Wide to engage idlers 1 and 6, PL 88.10 Item 20 .
Possible causes:
• Incorrectly aligned or damaged registration/ pre-heat Assembly idlers, PL 88.10 Item 20 .
Solution:
• Adjust or install new components as necessary.
If the noise repeats perform the following:
NOTE: W/ TAG 018 machines do not have air pumps install as standard. However, the preheat
air pumps in a replacement registration/preheat assembly will function when the unit is
installed, refer to service bulletin T8009-12-06.
• Enter dC330 code 88-008 Reg/Preheat Air Pumps to switch on the registration/pre-heat
air pump, PL 88.10 Item 5 .
Possible causes:
• Registration/pre-heat air pump.
Solution:
• Adjust or install new components as necessary.
Nips / Diverters
NOTE: A door cheat for the main door is not required.
Run the following components:
• Enter dC330 code 82-008 Nip D Solenoid to open the nip 'D' release solenoid, PL 70.30
Item 13 . Used for short-edge feed and fast color mode.