Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 535 / 1812

February 2013
2-511 ColorQube® 9303 Family
99-805-00 to 99-823-00
Status Indicator RAPs
99-811 Hard Refer to WD 9.10 . Check the DC cabling to the printhead roll adjust
motor 1. Measure the resistance at PJ303 on the marking unit driver
PWB for an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead roll adjust
motor 1. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead roll adjust motor 1. is drawing excessive power.
Install new components as necessary, printhead roll adjust motor 1,
PL
91.25 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP.
99-812 Soft Go to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP. Check
printhead 2 roll adjust motor.
99-813 Hard Refer to WD 9.9 . Check the DC cabling to the printhead roll adjust motor
2. Measure the resistance at PJ102 on the marking unit driver PWB for
an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead roll adjust
motor 2. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead roll adjust motor 2 is drawing excessive power.
Install new components as necessary, printhead roll adjust motor 2,
PL
91.20 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP.
99-814 Soft Go to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP. Check
printhead 3 roll adjust motor.
99-815 Hard Refer to WD 9.10 . Check the DC cabling to the printhead roll adjust
motor 3. Measure the resistance at PJ303 on the marking unit driver
PWB for an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead roll adjust
motor 3. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead roll adjust motor 3. is drawing excessive power.
Install new components as necessary, printhead roll adjust motor 3,
PL
91.25 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP.
99-816 Soft Go to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP. Check
printhead 4 roll adjust motor.
99-817 Hard Refer to WD 9.9 . Check the DC cabling to the printhead roll adjust motor
4. Measure the resistance at PJ102 on the marking unit driver PWB for
an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead roll adjust
motor 4. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead roll adjust motor 4 is drawing excessive power.
Install new components as necessary, printhead roll adjust motor 4,
PL
91.20 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP.
Check printhead 4 roll adjust motor.
Table 1 PEST codes and action
Code Hard/Soft Action
99-818 Soft Go to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP. Check
printhead roll adjust motors.
99-819 Soft Go to the 91-506-00 to 91-509-00 Roll Motor Over Current RAP. Check
printhead roll adjust motors.
99-820 Soft Go to the 91-504-00, 91-505-00 Printhead Stitch Motor Over Current
RAP. Check printhead 1 stitch adjust motor.
99-821 Hard Refer to WD 9.10 . Check the DC cabling to the printhead stitch adjust
motor 1. Measure the resistance at PJ303 on the marking unit driver
PWB for an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead stitch adjust
motor 1. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead stitch adjust motor 1. is drawing excessive power.
Install new components as necessary, printhead stitch adjust motor 1,
PL 91.25 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-504-00, 91-505-00 Printhead Stitch Motor Over Current
RAP. Check printhead 1 stitch adjust motor.
99-822 Soft Go to the 91-504-00, 91-505-00 Printhead Stitch Motor Over Current
RAP. Check printhead 2 stitch adjust motor.
99-823 Hard Refer to WD 9.9 . Check the DC cabling to the printhead stitch adjust
motor 2. Measure the resistance at PJ102 on the marking unit driver
PWB for an open or short circuit and to the chassis for a short circuit.
If a fault is found, repeat the measurement at the printhead stitch adjust
motor 2. If a short is measured, the marking unit driver PWB may be
damaged and be reported as an ‘open’ error. If short error is reported,
the printhead roll adjust motor 2 is drawing excessive power.
Install new components as necessary, printhead stitch adjust motor 2,
PL 91.20 Item 4 , marking unit driver PWB, PL 92.10 Item 4 .
Refer to the 91-504-00, 91-505-00 Printhead Stitch Motor Over Current
RAP. Check printhead 2 stitch adjust motor.
Table 1 PEST codes and action
Code Hard/Soft Action