Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 379 / 1812

February 2013
2-355 ColorQube® 9303 Family
89-531-00 to 89-545-00, 89-550-00, 89-551-00
Status Indicator RAPs
89-531-00 to 89-545-00 Registration Process Error RAP
89-531-00 The registration sensor (10) failed to detect the leading edge.
89-532-00 The registration sensor (10) timed out or failed to complete normally.
89-533-00 The registration sensor (10) generated a floating point exception.
89-534-00 The registration sensor (10) scan failed.
89-540-00 Sensor 10 post registration processing failure.
89-541-00 Sensor 10 post processing leading edge not detected.
89-542-00 Sensor 10 post processing lateral edge not detected.
89-543-00 Sensor 10 post processing leading edge error.
89-544-00 Sensor 10 post processing lateral edge error.
89-545-00 Sensor 10 post processing leading edge crossing too small.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury
• Check for damage or debris that restricts movement of the assembly.
• Check for dust or media debris around the registration scan bar.
Procedure
Enter dC715 Active registration control and disable registration control. Enter dC969 Clean Ink
Smears and run the routine. The pages exit the registration / preheat assembly.
Y
N
Go to the
89-110-00 to 89-113-00, 89-129-00 Media Path Sensor 10 Failure RAP.
Install a new registration / preheat assembly, PL 88.10 Item 1
NOTE: Calibration of the registration / preheat assembly, dC625 , is only required when:
• The registration / preheat assembly is removed or replaced.
• The horizontal transport assembly is removed or replaced.
Calibration of the registration / preheat assembly is NOT required when:
• A printhead is replaced.
• The IOD assembly is removed or replaced.
89-550-00, 89-551-00 Media Registration Error RAP
89-550-00 The registration sensor detected excessive skew on the incoming media.
89-551-00 The registration sensor detected excessive offset on the incoming media.
Initial Actions
• Ensure that the tray 3 paper tray guides are set correctly, ADJ 73.1 .
• Check and clean the vertical and horizontal transport nip rolls up to the registration / pre-
heat assembly.
• Perform dC625 Registration / preheat Calibration routine.
Procedure
Run the job from a different tray. The fault still occurs.
Y
N
Check the tray from which the fault occurs and install new components as necessary.
Enter dC330 code 82-007 Nip C release solenoid, SOL83-007. Press Start. The solenoid
energizes.
Y
N
Go to
WD 8.1 . Check SOL83-007. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
• PJ303, Media path driver PWB .
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
•
Nip C release solenoid, PL 82.15 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Enter dC330 code 82-008 Nip D release solenoid, SOL83-008. Press Start. The solenoid
energizes.
Y
N
Go to
WD 8.3 . Check SOL83-008. Refer to:
• GP 12 How to Check a Solenoid or Clutch.
• PJ405, Media path driver PWB .
• 01J +50V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Nip D release solenoid, PL 70.30 Item 13 .
• Media path driver PWB, PL 1.15 Item 5 .
Check the vertical and horizontal transport rolls and drive belts.Install new parts as necessary.
Refer to
PL 82.10 for the vertical transport and PL 82.15 for the horizontal transport.
If the error persists, install a new registration / preheat assembly PL 88.10 Item 1 .
NOTE: Calibration of the registration / preheat assembly, dC625 is only required when:
• The registration / preheat assembly is removed or replaced,
• The horizontal transport assembly is removed or replaced.
Calibration of the registration / preheat assembly is NOT required when:
• A printhead is replaced.
• The IOD assembly is removed or replaced.