Xerox ColorQube 9303 Series, Руководство по обслуживанию

Страница: 339 / 1812

February 2013
2-315 ColorQube® 9303 Family
73-101-00 to 73-161-00, 73-212-00
Status Indicator RAPs
Enter dC330 code 70-025 3 tray transport motor, MOT70-025, PL 73.16 Item 3 . Press Start.
The motor runs.
Y
N
Refer to
WD 7.5 . Check 3 tray transport motor, MOT70-025. Refer to:
• GP 10 How to Check a Motor.
• PJ953, 3 tray module PWB
• 01H +24V Distribution RAP
• 01L 0V Distribution RAP
Install new components as necessary:
• 3 tray module transport motor, PL 73.16 Item 3 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
The transport rolls rotate.
Y
N
Check the gears and drive belt,
PL 73.16 .
CAUTION
To prevent damage to the feed mechanism, the paper tray must be pulled out before MOT 73-
001 is run in diagnostics.
Enter dC330 code 73-001 tray 3 feed motor, MOT73-001, PL 81.30 Item 22 . Press Start. The
motor runs.
Y
N
Refer to
WD 7.4 . Check tray 3 feed motor, MOT73-001. Refer to:
• GP 10 How to Check a Motor.
• PJ953, 3 tray module PWB.
• 01H +24V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary:
• Tray 3 feed motor, PL 81.30 Item 22 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Perform the following:
• Check the feed roll assembly, PL 81.30 Item 11 .
• Check the tray 3 feed assembly, PL 81.30 Item 1 . Refer to REP 81.2 and check the feed
head housing location.
• Check the tray is level. Perform the following:
1. Remove the tray front cover.
2. Elevate the tray to the stack height position.
3. Hold the elevator drive gear and pull out the tray. Check that the tray is level.
4. If the tray is not level then install new elevator cables, PL 73.15 Item 18 .
• If the fault still occurs, check the following:
– The takeaway roll 3, PL 81.35 Item 16 .
– The transport roll 2, PL 81.35 Item 15 .
– The transport roll 1, PL 81.35 Item 14 .
73-212-00 Tray 3 Elevate Encoder Failure RAP
73-212-00 Tray 3 encoder failure on hoist.
Initial Actions
WARNING
Ensure that the electricity to the machine is switched off while performing tasks that do
not need electricity. Refer to
GP 14 . Disconnect the power cord. Electricity can cause
death or injury. Moving parts can cause injury.
• Check that the encoder is located correctly, PL 73.16 Item 2 .
• Check that the encoder sensor and wheel are clean.
Procedure
Pull out the relevant tray and allow it to move fully down. Close the tray. The tray moves up.
Y
N
Go to
73-215-00 Tray 3 Hoist Failure RAP.
Enter dC140 Analog Monitor select code 073-003 3TM elevator encoder. Perform the routine
for the encoder. The encoder routine is good.
Y
N
Refer to
WD 7.5 . Check the 3TM elevator encoder sensor, Q73-003. Refer to:
• GP 11 How to Check a Sensor.
NOTE: In this check place a piece of paper in the sensor. The check is difficult due
to the problem in moving the timing disc.
• PJ954, 3 tray module PWB .
• 01D +5V Distribution RAP.
• 01L 0V Distribution RAP.
Install new components as necessary.
• Tray 3 elevator motor, PL 73.16 Item 2 .
• 3 tray module PWB, PL 73.16 Item 4 .
• Media path driver PWB, PL 1.15 Item 5 .
Check the encoder wheel for damage and that it is located on the motor correctly. If necessary
install new components,
PL 73.16 .
A