manualshive.com logo in svg

Texas Instruments SimpleLink Ethernet MSP432E401Y, Техническое справочное руководство

Поделиться
Скачать
Texas Instruments SimpleLink Ethernet MSP432E401Y Скачать руководство пользователя страница 425

www.ti.com

System Control Registers

425

SLAU723A – October 2017 – Revised October 2018

Submit Documentation Feedback

Copyright © 2017–2018, Texas Instruments Incorporated

System Control

Table 4-186. PCADC Register Field Descriptions

Bit

Field

Type

Reset

Description

31-2

RESERVED

R

0x0

1

P1

R/W

0x1

ADC Module 1 Power Control. The Pn bit encodings do not apply if
the corresponding bit in the RCGCADC, SCGCADC, or DCGCADC
register is clear.

0x0 = The ADC module 1 is not powered and does not receive a
clock. In this case, the state of the module is not retained. This
configuration provides the lowest power consumption state.

0x1 = The ADC module 1 is powered but does not receive a clock. In
this case, the module is inactive.

0

P0

R/W

0x1

ADC Module 0 Power Control. The Pn bit encodings do not apply if
the corresponding bit in the RCGCADC, SCGCADC, or DCGCADC
register is clear.

0x0 = The ADC module 0 is not powered and does not receive a
clock. In this case, the state of the module is not retained. This
configuration provides the lowest power consumption state.

0x1 = The ADC module 0 is powered but does not receive a clock. In
this case, the module is inactive.

Содержание SimpleLink Ethernet MSP432E401Y


























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды