Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 266

Страница: 266 / 327

Service and maintenance of machine

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

266

8.11

Transport floor

WARNING

Risk of becoming entangled, wound up or risk of shearing due
to the transport floor accidentally starting!

Only enter the cargo space with the machine switched off and the
transport floor secured against accidental starting.

Ensure that the transport floor
strips on the right-hand and left-
hand side do not bump against
the frame (1)!

Equally shorten the chains of the
transport floor if the tension path
of the chain tensioners is no
longer sufficient to retighten the
chains!

Fig. 131

The chains of the transport floor:

•

must be tightened equally, but not too firmly.

•

are only allowed to sag slightly.

8.11.1

Shorten and tighten transport floor chains

WARNING

Risk to eyes due to blown-away abrasive particles when cutting
chain links by means of a right-angle grinder!

Wear protective goggles when cutting the chain links by means of
the right-angle grinder.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды