Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 24

Страница: 24 / 327

Product description

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

(1)

Feed line with hose coupling (red)

(2)

Brake line with hose coupling (yellow)

(3)

Blank connection for brake line

(4)

Trailer brake valve

(5)

ALB regulator (mechanical)

(6)

Release valve

(7)

Operating element for release valve (can
only be actuated in uncoupled condition):

•

Push in as far as it will go and the service
brake system releases, e.g. for
manoeuvring the unhitched machine

•

Pull out as far as it will go and the machine
is braked again by means of the system
pressure coming from the air reservoir

(8)

Diaphragm brake cylinder

(9)

Compressed-air reservoir

(10) Drain valve

(11) Test connection in front of ALB regulator

(12) Test connection behind ALB regulator

(13) Test connection, diaphragm brake cylinder

(14) Test connection, compressed-air reservoir

(15) Parking brake

Fig. 6

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды