Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 263 | Manualshive

Страница: 263 / 327

background image

Service and maintenance of machine

263

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

8.10.8

Set rpm sensor "Beaters"

WARNING

Risk of crushing and being drawn in during setting of rpm
sensor "Beaters" if the machine is unintentionally powered or
hydraulic functions are accidentally carried out!

Secure tractor and machine against accidental starting and rolling
before setting the sensor.

10.



Fasten the sensor (3) such that the
distance between the sensor and the bolt
head (2) is approx. 3 mm.



The light emitting diode lights up.

11.



Screw the sensor in this position.

Fig. 127

8.10.9

Sensor "Tailgate closed" (forage wagon and forage wagon with dosing unit)

WARNING

Risk of crushing and being drawn in during setting of the
"Tailgate closed" sensor if the machine is unintentionally
powered or hydraulic functions are accidentally carried out!

Secure tractor and machine against accidental starting and rolling
before setting the sensor.

1.



Close the tailgate completely.

2.



Fasten the sensor retaining plate (2) such
that the distance between the sensor and
the trip pad (1) is approx. 3 mm.



The light emitting diode lights up.

3.



Screw the sensor in this position.

Fig. 128

«
...
261
262
263
264
265
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: ABB Страницы: 14

Бренд: DARKSTAR TECHNOLOGIES Страницы: 4

Бренд: TDW Страницы: 2

Бренд: Taurus Страницы: 25

Бренд: Vancare Страницы: 3

Бренд: Paitec Страницы: 14

medialon Showmaster Go

Бренд: 7th Sense Страницы: 9

Бренд: Gatekeeper Страницы: 8

Bure Rise & Go DB 56-309

Бренд: Gate Страницы: 8

Бренд: Garmin Страницы: 2

Бренд: ABB Страницы: 154

Бренд: Lencarta Страницы: 6

Бренд: Bondura Страницы: 10

Бренд: Beaumont Страницы: 7

Бренд: Hill-Rom Страницы: 28

Бренд: Kärcher Страницы: 28

Бренд: Digilent Страницы: 14

Бренд: Fluke Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды