Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 327

background image

Safety instructions

81

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

87010271

Risk to any part of the body of being crushed and/or risk of impact if people
stand within the hazardous area of the machine!

This risk may cause most serious injuries or even death.

People are not allowed within the hazardous area of the machine as long as the
tractor engine is running.

87010276

Risk to any part of the body of being drawn in or becoming entangled due to
powered working tools!

This risk may cause most serious injuries or even death.

•

Keep sufficient safe distance to powered working tools.

•

Ensure that people keep sufficient safe distance to powered working tools.

87010278

Risk of becoming entangled and wound up due to the powered propeller
shaft!

This risk may cause most serious injuries or even death.

•

Keep sufficient safe distance to the propeller shaft as long as the tractor
engine is running with the propeller shaft coupled / the hydraulic system
connected.

•

Ensure that people keep sufficient safe distance to the powered propeller
shaft.

87010279

Risk of cuts for fingers and hands due to working on sharp / sharp-edged
working tools!

This risk may cause most serious injuries including loss of limbs.

Observe the information in the operating instructions before carrying out work on
sharp working tools.

87010280

Risk to hands and arms of being drawn in or becoming entangled in moving
power transmission parts!

This risk may cause most serious injuries including loss of limbs.

Never open nor remove protective devices as long as the tractor engine is running
with the propeller shaft coupled/the hydraulic/electronic system connected.

«
...
79
80
81
82
83
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: Makita Страницы: 8

Бренд: VECTECH Страницы: 5

Бренд: Abbott Страницы: 2

FreeStyle Libre

Бренд: Abbott Страницы: 3

Бренд: abc Страницы: 8

Precision2 HP2 Series

Бренд: B-K lighting Страницы: 6

Бренд: Zero Hand Truck Страницы: 38

Бренд: B-K lighting Страницы: 3

Бренд: Rangevision Страницы: 28

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: Waves Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды