Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 126 | Manualshive

Страница: 126 / 327

background image

Commissioning

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

126

5.14

Manoeuvre unhitched machine by means of a manoeuvring vehicle

WARNING

Risk of crushing, entanglement and impact for people if the
machine accidentally rolls during manoeuvring work with the
service brake released!

Tightly connect the machine with the braked manoeuvring vehicle
before releasing the service brake by means of the hand lever at the
brake pressure regulator. Now the machine must be exclusively
slowed down by the manoeuvring vehicle.

1.



Hitch the machine to the braked
manoeuvring vehicle.

2.



Release the parking brake of the machine.

3.



Swivel the hand lever at the brake
pressure regulator to "Release" position.



The service brake is released and the
machine can be manoeuvred.

4.



Use the manoeuvring vehicle to
manoeuvre the machine.

5.



Apply the parking brake of the
manoeuvring vehicle after manoeuvring.

6.



Swivel the hand lever at the brake
pressure regulator back to its initial
position after manoeuvring.



The system pressure from the air reservoir
slows the machine down.

7.



Apply the parking brake of the machine.

8.



Unhitch the machine from the manoeuvring
vehicle.

Fig. 69

«
...
124
125
126
127
128
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Giga-Vitesse CFS 3602

Бренд: B&K Страницы: 8

Бренд: Zetec Страницы: 23

Бренд: lancer Страницы: 3

Бренд: lancer Страницы: 12

Бренд: R2 Страницы: 26

Бренд: Macht Dental Страницы: 8

Бренд: Vatech Страницы: 137

Бренд: Vatech Страницы: 68

Бренд: Varytec Страницы: 52

Бренд: Baileigh Industrial Страницы: 12

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: A.J.Antunes Страницы: 24

Бренд: B&G Страницы: 2

Бренд: Posture Pump Страницы: 2

Бренд: Stiga Страницы: 20

GPSMAP 9 3 Series

Бренд: Garmin Страницы: 222

Бренд: Unika Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды