Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 214

Страница: 214 / 327

Use of machine

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

214

7.1

Transport journeys

•

Additionally observe the information in the following chapters
when carrying out transport journeys:



"Safety instructions for the operator"



"Basic safety instructions"

•

Before carrying out transport journeys, check



the supply lines for proper connection,



the lighting system for damage, proper functioning and
cleanliness,



the brake and hydraulic system for visible defects,



whether the parking brake has been completely
released,



the brake system for proper functioning.

WARNING

Risk of dangerous travelling situations due to accidental
actuation of hydraulic functions during transport journeys!

Switch the

Road Travel Mode

on before carrying out transport

journeys.

The covering system (optional extra) must be closed during
transport journeys.

Observe the fact that the braking axle needs to run in during the first
service hours

– the brake lining is adjusting to the brake drum. Full

braking power is only reached after this running-in period.

Check the brake system for proper functioning before carrying out
transport journeys.

If the folding drawbar is equipped with a drawbar suspension, the
hydraulic cylinders of the folding drawbar must be extended by
approx. 20 mm before switching the road travel mode on.

The drawbar suspension will not work if the folding drawbar is
lowered to its end position.



Lower the lift axle completely if available.



Only with the lift axle completely lowered is the ALB regulator able to properly control the
required braking force.



Deactivate the automatic charging system and close the front panel.



Activate the

Road Travel Mode

on your control set.



With the

Road Travel Mode

switched on:



the

Road Travel

menu appears,

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды