Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 235

Страница: 235 / 327

Service and maintenance of machine

235

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

8.3

Cleaning work

•

Regularly clean the machine! Regular cleaning of the machine
is the precondition for proper maintenance and makes
operation of the machine easier.

•

Continuously inspect the machine for corrosion damage!
Remedy corrosion damage by touching up paintwork.

•

Never treat brake lines, air pipes and hydraulic hose pipes with
benzine, benzol, paraffin or mineral oils.

•

Lubricate the machine after cleaning, especially after cleaning
by means of a pressure washer / steam blaster or fat dissolving
agents.

•

Observe the legal provisions for handling and disposal of
cleaning agents.

8.3.1

Cleaning by means of pressure washer / steam blaster

It is absolutely imperative to observe the following when using a
pressure washer / steam blaster for cleaning:

•

The maximum admissible injection pressure is 80 bar.

•

Water temperature: max. 60°C.

•

Do not clean electrical components.

•

Do not clean chromium-plated components.

•

Never aim the cleaning nozzle jet of the pressure washer /
steam blaster



directly at lubrication points and bearings.



directly at hydraulic and electrical components.

•

Always keep a minimum nozzle distance of 300 mm between
the cleaning nozzle and the machine.

•

Never aim the cleaning nozzle jet at the vehicle parts at right
angles. The nozzle spray angle must at least be 25°.

•

Do not use any chemical additives.

•

Observe the safety instructions when handling pressure
washers.

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации

Результаты поиска

Содержание Giga-Vitesse CFS 3602

Отзывы:

Похожие инструкции для Giga-Vitesse CFS 3602

Бренды по названию

Популярные бренды