Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 153 | Manualshive

Страница: 153 / 327

Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 153

Operation

153

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO 03.18

6.1.3.29 Unlock steering axle in SES system

In case of the electro-hydraulic forced steering axle system, the

key has no function.

1.

Press the

key once.

Discharge Mode A I

or

A II

respectively is

deactivated. The steering axle is force-
steered and follows the turning radius of
the corner during cornering. The "Steering
axle force-steered" symbol appears and a
horn sound is emitted.

If the symbol is flashing and a horn sound
is emitted, there is a malfunction in the
steering system. The passive steering is
activated. Check the steering system.

The screen shows:

Only in discharge mode A I or A II
respectively:

1.

Press the

key once.

The steering axle is force-steered.

2.

Press the

key again.

The steering axle is locked in "Straight"
position. The "Steering axle locked"
symbol appears and a horn sound is
emitted.

If the symbol is flashing, the steering axle
could not be completely locked. Check the
steering system.

The screen shows:

«
...
151
152
153
154
155
...
»

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов