manualshive.com logo in svg

Strautmann Giga-Vitesse CFS 3602, Руководство по эксплуатации, Страница: 160 / 327

Поделиться
Скачать
Strautmann Giga-Vitesse CFS 3602 Скачать руководство пользователя страница 160

Operation

 

 

 

Giga-Vitesse CFS 3602 - 4402, Giga-Vitesse CFS 3602 DO - 4402 DO   03.18 

160 

 

6. 

Press and hold the 

 key once. 

 

The 

SET

 menu appears. 

7. 

The person in the cargo space swivels the 
sensing band to the bottom position which 
shall be the automatic start position for the 
transport floor. 

8. 

Press the 

 key once to start the 

calibration mode. 

 

The display "KAL" (5) appears. 

 

 

 

 

9. 

The person in the cargo space swivels the sensing band to the top position which shall be the 
start position for the transport floor running at maximum feed rate. 

10. 

Press the 

 key again. 

11. 

Press the 

 key once to acknowledge the settings and to finish the calibration procedure. 

 

A horn sounds. 

12. 

Check whether the set range is appropriate by manually moving the sensing band from the 
bottom position (indicated value: 0) to the top position (indicated value: 100). Adjust the range in 
case of a collision. 

13. 

Press the 

 key once. 

 

The 

Working

 menu appears. 

 

 

 

 

 

Содержание Giga-Vitesse CFS 3602








































































































































































































































































































































Отзывы:

Нет отзывов